FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Forends and Rail Systems

Forends and Rail Systems

Grid List

Set Ascending Direction

11-15 of 15

Page:
  1. 1
  2. 2
  1. 13"  GEN II Transformer Rail for AR-15
    $154.95

    Your rail now automatically ships with (6)  Snakeskin polymer grip panels at not charge!

    GEN II barrel nut design is lighter, simpler, and easier to install!  Just torque to the recommend barrel nut torque setting, slide rail over and install 8 set screws and you are done!  No need to time barrel nut or align threaded holes, plus a cleaner look than the original Transformer Rail!

     M-LOK and Keymod....ON THE SAME RAIL!

    The Transformer Rail comes with the rail, barrel nut, barrel nut wrench, and six polymer grip panels.  Additional panels available in pulldown menus!

    Specifications:

    • AR-15 Aluminum Free Float rail system with ability to intermix Keymod, M-LOK, and polymer grip panels

    • Dimensions: 13” length, 1.5” exterior width, 1.09” interior clear width

    • Weight: 7.4 ounces for rail, 1.5 ounces for barrel nut, under 0.3 ounces per panel

    • Weight installed: 8.9 ounces (only adds 7.4 ounces as original barrel nut is removed)

    • Barrel nut material and finish: 6061 6061 T6 aluminum with Milspec Type III Black hardcoat anodizing

    • Rail material and finish: 6061 T6 aluminum with Milspec Type III Black hardcoat anodizing

    • Panel material and finish: 6061 black anodized aluminum and proprietary polymer 

    • Ships with Transformer Rail, Barrel Nut, Barrel Nut Wrench, all hardware, 6 polymer grip panels, allen wrenches, and instruction sheet

    • Interchangeable Transformer panel system allows for mixing of Keymod, M-LOK, and polymer grip panels. Other panels, such as Picatinny, will launch after initial release

    • Six Transformer panel mounting locations

    • GEN II barrel nut design is lighter, simpler, and easier to install!  Just torque to the recommend barrel nut torque setting, slide rail over and install 8 set screws and you are done!  No need to time barrel nut or align threaded holes, plus a cleaner look than the original Transformer Rail!

    • Eight QD sling swivel pockets- three on each side and two underneath

    • Clears low profile gas blocks and works with all gas system lengths (carbine, midlength, rifle)

    • 100% Designed and Made in the USA

    • Multiple Patents Pending

    Learn More
  2. X95 Cantilever Forend  ( Taller Height Rail )
    $234.95

    Out of stock

    PLEASE NOTE:   THE GEN I  FOREND HAS BEEN DISCONTINUED.  IT HAS BEEN REPLACED WITH AN IMPROVED GEN II FOREND THAT MORE SECURELY MOUNTS THE FOREND TO THE TOP RAIL.  PURCHASE THE GEN II FOREND HERE:

    https://manticorearms.com/shop-by-rifle/x95-tavor-products/x95-cantilever-forend-ar-15-height-rail-gen-ii

    The Patent Pending  X95 Cantilever Forend offers a wealth of features at an incredible price.  To solve some of the inherent issues of how to securely mount a forend to the X95 without contacting the barrel we had to think outside the box, and the solution was a two part system.

    The first component consists of a 39 slot picatinny top rail and cover plate assembly that is raised to the proper height to work with standard AR-15 iron sights and optics (i.e. most all sighting components on the market these days).  In addition the top rail is cut for the 300 blackout gas adjustment access in case you are mounting on a 300 Blackout X95.

    The second component is the forend itself which is 2" longer than the OEM forend, features 3 rows of M-LOK (13 slots) on each side plus 2 QD points on each side,  and  5 slots of M-LOK on the underside.  The center row of M-LOK on the sides and the underside row on M-LOK is centered on the bore line making it much easier to zero lasers and other items that are bore line sensitive.   The top of the forend features two L-shaped tabs that engage matching slots on the top rail.  To install the forend portion just slide the forend into the slots on the top rail along the axis of the barrel, make sure the alignment tab on the underside engages the opening in the receiver,  tighten the cross bolt screw and you are ready to go with a rock solid mounted forend.  This along-the-bore-axis installation allows the additional benefit of being able to install a suppressor up to 1.5" in diameter on the barrel and the forend can easily be slid on and off without need to remove the suppressor.

    Not wanting to leave an opening where the lower plastic tab of the OEM forend engages, we have included a polymer filler block that blends perfectly with the receiver to keep everything closed up and tidy.

    One last benefit- with X95 Cantilever forend THE BARREL IS NOW FREE FLOATED.  No more contact of the barrel as with the OEM polymer forend and its two barrel mounted polymer support points, as the X95 Cantilever Forend is completely supported by the top rail and the receiver.

    Total weight of the system is 1 lb 7.4 ounces compared to the OEM 1 lb 2.5 ounces.  Only 3.9 ounces more than the OEM forend at a gain of all aluminum construction, the ability to sleeve a suppressor, a longer and higher and more useful top rail, and almost 2" of additional forend with a slimmer profile plus M-LOK compatibility and integral QD points.  Not a bad deal for 3.9 extra ounces, is it?  

    The X95 Cantilever Forend  is Patent Pending, and manufactured of 6061 black milspec hardcoated aluminum (plus a polymer filler block) 100% right here in the USA.

    Material:  6061 aluminum and polymer

    Finish:  Type III milspec hardcoat black anodizing 

    Weight:   1 lb 7.4 ounces

    Length:  For 16" and 18.5" barreled guns (2" longer than OEM forend)

    100% designed and manufactured in the USA

    Learn More
  3. ALFA RAIL Keymod Forend Mini Draco
    $176.95

    Out of stock

    THE MA-12400 ALFA HANDGUARD WILL ONLY FIT THE MINI DRACO.

    The ALFA RAIL Keymod forend Min Draco gives the ability to use keymod accessories, mount an optic on the top picatinny, and even features an integral hand stop and QD sling swivel mounting point. The forend is installed like the standard Mini Draco handguard and is held in place by both the bolt on the underside and also features a flange that prevents the handguard from moving forward if the screw comes loose.

    An extremely precise and tight fight, in addition to careful design of the interface points with weapon ensures that the mounting is rock solid. The forend weighs only 4 oz, or approximately the same as the wood forend, yet offers much more in features. Manufactured from solid billets of 6061 T6 aluminum and anodized black the ALFA RAIL upper and lower include instructions and all hardware necessary for installation and are 100% made in the USA.

    Learn More
  4. ALFA RAIL Keymod Forend for stamped AK
    $118.95

    Out of stock

    PLEASE NOTE: THE ALFA LOWER FOREND OPTION FOR $119 IS ONLY THE LOWER PORTION, THE UPPER HANDGARD IS NOT INCLUDED WITH THIS OPTION! THE MA-11275 ALFA HANDGUARD WILL ONLY FIT STANDARD STAMPED 'EURO' AND 'CHINESE' AK'S.

    THIS MODEL WILL NOT FIT YUGO M-70/N-PAP/O-PAP, KRINKOVS, M92'S, UNCONVENRTED VEPR'S OR UNCONVERTED SAIGAS.

    The ALFA RAIL Keymod forend for the standard pattern AK gives the look and feel of a more traditional AK forend while giving the ability to mount Keymod accessories and other optional components, all while mounting exactly like the original handguard.

    The forend is simply installed like any standard AK handguard and is held in place by the front handguard retainer. An extremely precise and tight fight, in addition to careful design of the interface points with weapon ensures that the mounting is rock solid.

    Weighing 3.5 ounces it is actually almost an ounce lighter than the original polymer forend, yet several times stronger. An optional Superlow Optics Mount Upper which weighs only 2 ounces allows you to mount an Aimpoint Micro on its picatinny top rail and have co-witness with the iron sights.

    The ALFA RAIL lower forend will work with the standard polymer or wood upper handguard, or even with an Ultimak railed upper gas tube. Manufactured from solid billets of 6061 T6 aluminum and anodized black the ALFA RAIL upper and lower include instructions and all hardware necessary for installation and are 100% made in the USA.

    Material: 6061 aluminum

    Finish: Type III Milspec Hardcoat Black Anodizing

    Weight: 3.5 ounces lower rail, 2.0 ounces optional top cover

    Length: Standard AK forend

    100% designed and manufactured in the USA.

    Learn More
  5. 15"  GEN II Transformer Rail for AR-15
    $164.95

    Out of stock

    Your rail now automatically ships with (6)  Snakeskin polymer grip panels at no charge!

    GEN II barrel nut design is lighter, simpler, and easier to install!  Just torque to the recommend barrel nut torque setting, slide rail over and install 8 set screws and you are done!  No need to time barrel nut or align threaded holes, plus a cleaner look than the original Transformer Rail!

     M-LOK and Keymod....ON THE SAME RAIL!

    The Transformer Rail comes with the rail, barrel nut, barrel nut wrench, and six polymer grip panels.  Additional types of panels can be added below!

    Specifications:

    • AR-15 Aluminum Free Float rail system with ability to intermix Keymod, M-LOK, and polymer grip panels

    • Dimensions: 15” length, 1.5” exterior width, 1.09” interior clear width

    • Weight: 8.4 ounces for rail, 1.5 ounces for barrel nut, under 0.3 ounces per panel

    • Weight installed: 9.9 ounces (only adds 7.4 ounces as original barrel nut is removed)

    • Barrel nut material and finish: 6061 6061 T6 aluminum with Milspec Type III Black hardcoat anodizing

    • Rail material and finish: 6061 T6 aluminum with Milspec Type III Black hardcoat anodizing

    • Panel material and finish: 6061 black anodized aluminum and proprietary polymer 

    • Ships with Transformer Rail, Barrel Nut, Barrel Nut Wrench, all hardware, 6 polymer grip panels, allen wrenches, and instruction sheet

    • Interchangeable Transformer panel system allows for mixing of Keymod, M-LOK, and polymer grip panels. Other panels, such as Picatinny, will launch after initial release

    • Six Transformer panel mounting locations

    • GEN II barrel nut design is lighter, simpler, and easier to install!  Just torque to the recommend barrel nut torque setting, slide rail over and install 8 set screws and you are done!  No need to time barrel nut or align threaded holes, plus a cleaner look than the original Transformer Rail!

    • Eight QD sling swivel pockets- three on each side and two underneath

    • Clears low profile gas blocks and works with all gas system lengths (carbine, midlength, rifle)

    • 100% Designed and Made in the USA

    • Multiple Patents Pending

    Learn More

Grid List

Set Ascending Direction

11-15 of 15

Page:
  1. 1
  2. 2