FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Forends and Rail Systems

Forends and Rail Systems

Grid List

Set Descending Direction

1-10 of 17

Page:
  1. 1
  2. 2
  1. 13"  GEN II Transformer Rail for AR-15
    $154.95

    Your rail now automatically ships with (6)  Snakeskin polymer grip panels at not charge!

    GEN II barrel nut design is lighter, simpler, and easier to install!  Just torque to the recommend barrel nut torque setting, slide rail over and install 8 set screws and you are done!  No need to time barrel nut or align threaded holes, plus a cleaner look than the original Transformer Rail!

     M-LOK and Keymod....ON THE SAME RAIL!

    The Transformer Rail comes with the rail, barrel nut, barrel nut wrench, and six polymer grip panels.  Additional panels available in pulldown menus!

    Specifications:

    • AR-15 Aluminum Free Float rail system with ability to intermix Keymod, M-LOK, and polymer grip panels

    • Dimensions: 13” length, 1.5” exterior width, 1.09” interior clear width

    • Weight: 7.4 ounces for rail, 1.5 ounces for barrel nut, under 0.3 ounces per panel

    • Weight installed: 8.9 ounces (only adds 7.4 ounces as original barrel nut is removed)

    • Barrel nut material and finish: 6061 6061 T6 aluminum with Milspec Type III Black hardcoat anodizing

    • Rail material and finish: 6061 T6 aluminum with Milspec Type III Black hardcoat anodizing

    • Panel material and finish: 6061 black anodized aluminum and proprietary polymer 

    • Ships with Transformer Rail, Barrel Nut, Barrel Nut Wrench, all hardware, 6 polymer grip panels, allen wrenches, and instruction sheet

    • Interchangeable Transformer panel system allows for mixing of Keymod, M-LOK, and polymer grip panels. Other panels, such as Picatinny, will launch after initial release

    • Six Transformer panel mounting locations

    • GEN II barrel nut design is lighter, simpler, and easier to install!  Just torque to the recommend barrel nut torque setting, slide rail over and install 8 set screws and you are done!  No need to time barrel nut or align threaded holes, plus a cleaner look than the original Transformer Rail!

    • Eight QD sling swivel pockets- three on each side and two underneath

    • Clears low profile gas blocks and works with all gas system lengths (carbine, midlength, rifle)

    • 100% Designed and Made in the USA

    • Multiple Patents Pending

    Learn More
  2. 15"  GEN II Transformer Rail for AR-15
    $164.95

    Your rail now automatically ships with (6)  Snakeskin polymer grip panels at no charge!

    GEN II barrel nut design is lighter, simpler, and easier to install!  Just torque to the recommend barrel nut torque setting, slide rail over and install 8 set screws and you are done!  No need to time barrel nut or align threaded holes, plus a cleaner look than the original Transformer Rail!

     M-LOK and Keymod....ON THE SAME RAIL!

    The Transformer Rail comes with the rail, barrel nut, barrel nut wrench, and six polymer grip panels.  Additional types of panels can be added below!

    Specifications:

    • AR-15 Aluminum Free Float rail system with ability to intermix Keymod, M-LOK, and polymer grip panels

    • Dimensions: 15” length, 1.5” exterior width, 1.09” interior clear width

    • Weight: 8.4 ounces for rail, 1.5 ounces for barrel nut, under 0.3 ounces per panel

    • Weight installed: 9.9 ounces (only adds 7.4 ounces as original barrel nut is removed)

    • Barrel nut material and finish: 6061 6061 T6 aluminum with Milspec Type III Black hardcoat anodizing

    • Rail material and finish: 6061 T6 aluminum with Milspec Type III Black hardcoat anodizing

    • Panel material and finish: 6061 black anodized aluminum and proprietary polymer 

    • Ships with Transformer Rail, Barrel Nut, Barrel Nut Wrench, all hardware, 6 polymer grip panels, allen wrenches, and instruction sheet

    • Interchangeable Transformer panel system allows for mixing of Keymod, M-LOK, and polymer grip panels. Other panels, such as Picatinny, will launch after initial release

    • Six Transformer panel mounting locations

    • GEN II barrel nut design is lighter, simpler, and easier to install!  Just torque to the recommend barrel nut torque setting, slide rail over and install 8 set screws and you are done!  No need to time barrel nut or align threaded holes, plus a cleaner look than the original Transformer Rail!

    • Eight QD sling swivel pockets- three on each side and two underneath

    • Clears low profile gas blocks and works with all gas system lengths (carbine, midlength, rifle)

    • 100% Designed and Made in the USA

    • Multiple Patents Pending

    Learn More
  3. 15"  MLOK Rail for AR-15
    $164.95

    Specifications:

    • AR-15 Aluminum Free Float rail system with M-LOK slots on sides and underside, picatinny on top.

    • Dimensions: 15” length, 1.5” exterior width, 1.09” interior clear width

    • Weight: 8.4 ounces for rail, 1.5 ounces for barrel nut

    • Weight installed: 9.9 ounces (only adds 7.4 ounces as original barrel nut is removed)

    • Barrel nut material and finish: 6061 6061 T6 aluminum with Milspec Type III Black hardcoat anodizing

    • Rail material and finish: 6061 T6 aluminum with  Milspec Type III Black hardcoat anodizing

    • Panel material and finish: 6061 black anodized aluminum and proprietary polymer 

    • Ships with M-LOK Rail, Barrel Nut, Barrel Nut Wrench, all hardware, allen wrenches, and instruction sheet

    • The Manticore GEN II barrel nut design is lighter, simpler, and easier to install!  Just torque to the recommend barrel nut torque setting, slide rail over and install 8 set screws and you are done!  No need to time barrel nut or align threaded holes, plus a cleaner look!

    • Clears low profile gas blocks and works with all gas system lengths (carbine, midlength, rifle)

    • 100% Designed and Made in the USA

    Learn More
  4. ARClight Pathfinder Tavor Forend
    $199.95

    ***PLEASE NOTE THIS IS A SPECIAL RUN WITH LIMITED QUANTITIES***

    The Pathfinder is a direct replacement for the OEM polymer Tavor SAR forend, is 7 inches longer than the OEM forend, and is intended to act as heat protection against a suppressor that is mounted to the barrel. The monolithic design allows it to sleeve over any suppressor up to 1.75" in diameter, and most suppressors will have approximately one inch visible out the front of the forend. ARC LOK slots on the entire surface let you mount any combination of accessories and grip further out on the gun, including on top of the front of the forend. It is made of completely monolithic construction, with no welds or fasteners to fail.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 13.4 ounces

    Length: ?? inches

    Designed and Manufactured 100% in the USA

    Learn More
  5. Bren 805 M-LOK Forend
    $79.95

    Machined from solid aluminum billet the Bren 805 M-LOK Forend allows for removal of the uncomfortable pictanny underside rail and replaces it with a nicely contoured underside forend with M-LOK slots on three faces.  It is a direct drop in replacement for the picatinny underside rail and only takes a few minutes to install and at 3.2 ounces only weighs slightly more than the stock 2.5 ounce component.

    Material: 6061 aluminum 

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 3.3 ounces

    Length: 7.25 inches

    Designed and Manufactured 100% in the USA

    Learn More
  6. Scorpion EVO 12" Carry Handle MLOK Forend
    $208.95

    PLEASE NOTE:  THIS FOREND IS ONLY RECOMMENDED FOR USE WITH A SCORPION EVO THAT HAS THE BULLPUP CONVERSION KIT INSTALLED.  THE SIGHT PLANE OF THE CARRY HANDLE WILL BE TOO HIGH FOR MOST USERS WHEN MOUNTED ON A STANDARD SCORPION EVO.

    The 12" Carry handle MLOK forend for Scorpion EVO offers no less than 23 slots of M-LOK across its 12" of length along with two integral QD points and is designed specifically to give a higher sight plane for use with Scorpion EVO's that are using the Bullpup Evo Conversion Kit. (It will fit all models of Scorpion EVO in standard configuration including the carbine, pistol, S2 Micro, but the sight plane will typically be too high for most users) .  Weighing in at 16.9 ounces including the mounting block it is actaully 0.5 ounces lighter than the 12" OEM polymer forend and has a built in carry handle to boot.  The forend will clear up to a 1.5" diameter suppressor, and uses an improved mounting block design which free floats the forend from the barrel. The forend comes with the forend, mounting block, and mounting hardware.  

    Material: 6061 aluminum

    Finish:  Type III Milspec black hardcoat andozing

    Weight: 16.9 ounces

    Length: 12 inches

    Designed and Manufactured 100% in the USA

    Learn More
  7. Scorpion EVO 12" MLOK Forend
    $158.95

    The 12" MLOK forend for Scorpion EVO offers no less than 27 slots of M-LOK across its 12" of length along with two integral QD points and will fit all models of Scorpion EVO including the carbine, pistol, S2 Micro, and EVO's using the Bullpup Conversion Kit .  Weighing in at 14.7 ounces including the mounting block it is actually 2.7 ounces lighter than the 12" OEM polymer forend.  The forend will clear up to a 1.5" diameter suppressor, and uses an improved mounting block design which free floats the forend from the barrel.  The forend comes with the forend, mounting block, and mounting hardwarde.  

    Material: 6061 aluminum

    Finish:  Type III Milspec black hardcoat andozing

    Weight: 14.7 ounces

    Length: 12 inches

    Designed and Manufactured 100% in the USA

    Learn More
  8. Scorpion EVO 15" Carry Handle MLOK Forend
    $229.95

    PLEASE NOTE:  THIS FOREND IS ONLY RECOMMENDED FOR USE WITH A SCORPION EVO THAT HAS THE BULLPUP CONVERSION KIT INSTALLED.  THE SIGHT PLANE OF THE CARRY HANDLE WILL BE TOO HIGH FOR MOST USERS WHEN MOUNTED ON A STANDARD SCORPION EVO.

    The 15" Carry handle MLOK forend for Scorpion EVO offers no less than 49 slots of M-LOK across its 15" of length along with two integral QD points and is designed specifically to give a higher sight plane for use with Scorpion EVO's that are using the Bullpup Evo Conversion Kit. (It will fit all models of Scorpion EVO in standard configuration including the carbine, pistol, S2 Micro, but the sight plane will typically be too high for most users) .  Weighing in at 18.6 ounces including the mounting block it is only 1.2  ounces heavier than the 12" OEM polymer forend, yet gives an additional 3" of length to completely wrap the barrel or a suppressor and has a built in carry handle.  The forend will clear up to a 1.5" diameter suppressor, and uses an improved mounting block design which free floats the forend from the barrel. The forend comes with the forend, mounting block, and mounting hardwarde.  

    Material: 6061 aluminum

    Finish:  Type III Milspec black hardcoat andozing

    Weight: 18.6 ounces

    Length: 15 inches

    Designed and Manufactured 100% in the USA

    Learn More
  9. Scorpion EVO 15" MLOK Forend
    $178.95

    The 15" MLOK forend for Scorpion EVO offers no less than 44 slots of M-LOK across its 15" of length along with two integral QD points and will fit all models of Scorpion EVO including the carbine, pistol, S2 Micro, and EVO's using the Bullpup Conversion Kit .  Weighing in at 19.4 ounces including the mounting block it is only 2.0 ounces heavier than the 12" OEM polymer forend, yet gives an additional 3" of length to completely wrap the barrel or a suppressor.  The forend will clear up to a 1.5" diameter suppressor, and uses an improved mounting block design which free floats the forend from the barrel.  The forend comes with the forend, mounting block, and mounting hardwarde.  

    Material: 6061 aluminum

    Finish:  Type III Milspec black hardcoat andozing

    Weight: 19.4 ounces

    Length: 15 inches

    Designed and Manufactured 100% in the USA

    Learn More
  10. X95 Cantilever Forend  ( AR-15 Height Rail ) GEN II
    $234.95

     PLEASE NOTE:  The AR-15 Height top rail is cut to work with all calibers of Tavor X95.

    The X95 Cantilever Forend offers a wealth of features at an incredible price.  To solve some of the inherent issues of how to securely mount a forend to the X95 without contacting the barrel we had to think outside the box, and the solution was a two part system.

    The first component consists of a 39 slot picatinny top rail and cover plate assembly that is raised to the proper height to work with standard AR-15 iron sights and optics (i.e. most all sighting components on the market these days). In addition the top rail is cut for the 300 blackout gas adjustment access in case you are mounting on a 300 Blackout X95.

    The second component is the forend itself which is 2" longer than the OEM forend, features 3 rows of M-LOK (13 slots) on each side plus 2 QD points on each side,  and  5 slots of M-LOK on the underside.  The center row of M-LOK on the sides and the underside row on M-LOK is centered on the bore line making it much easier to zero lasers and other items that are bore line sensitive.   The top of the forend features two L-shaped tabs that engage matching slots on the top rail.  To install the forend portion just slide the forend into the slots on the top rail along the axis of the barrel, make sure the alignment tab on the underside engages the opening in the receiver,  tighten the cross bolt screw and you are ready to go with a rock solid mounted forend.  This along-the-bore-axis installation allows the additional benefit of being able to install a suppressor up to 1.5" in diameter on the barrel and the forend can easily be slid on and off without need to remove the suppressor.

    Not wanting to leave an opening where the lower plastic tab of the OEM forend engages, we have included a polymer filler block that blends perfectly with the receiver to keep everything closed up and tidy. The forend and top rail are connected via a tongue and groove rail system and are secured together with screws for stable mounting and no movement.

    One last benefit- with X95 Cantilever forend THE BARREL IS NOW FREE FLOATED.  No more contact of the barrel as with the OEM polymer forend and its two barrel mounted polymer support points, as the X95 Cantilever Forend is completely supported by the top rail and the receiver.

    Total weight of the system is 1 lb 7.4 ounces compared to the OEM 1 lb 2.5 ounces.  Only 3.9 ounces more than the OEM forend at a gain of all aluminum construction, the ability to sleeve a suppressor, a longer and higher and more useful top rail, and almost 2" of additional forend with a slimmer profile plus M-LOK compatibility and integral QD points.  Not a bad deal for 3.9 extra ounces, is it?  

    The X95 Cantilever Forend  is Patent Pending, and manufactured of 6061 black milspec hardcoated aluminum (plus a polymer filler block) 100% right here in the USA.

    Material:  6061 aluminum and polymer

    Finish:  Type III milspec hardcoat black anodizing 

    Weight:   1 lb 7.4 ounces

    Length:  For 16" and 18.5" barreled guns (2" longer than OEM forend)

    100% designed and manufactured in the USA

     

    Learn More

Grid List

Set Descending Direction

1-10 of 17

Page:
  1. 1
  2. 2