FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Forends and Rail Systems

Forends and Rail Systems

Grid List

Set Descending Direction

11-19 of 19

Page:
  1. 1
  2. 2
  1. ALFA RAIL Keymod Forend for Century C39V2 AK
    $118.95

    Out of stock

    Rock Solid, easy to install, and direct fit for most rifles

    Learn More
  2. Scorpion EVO 15" Carry Handle MLOK Forend
    $230.00

    Out of stock

    PLEASE NOTE:  THIS FOREND IS ONLY RECOMMENDED FOR USE WITH A SCORPION EVO THAT HAS THE BULLPUP CONVERSION KIT INSTALLED.  THE SIGHT PLANE OF THE CARRY HANDLE WILL BE TOO HIGH FOR MOST USERS WHEN MOUNTED ON A STANDARD SCORPION EVO.

    The 15" Carry handle MLOK forend for Scorpion EVO offers no less than 49 slots of M-LOK across its 15" of length along with two integral QD points and is designed specifically to give a higher sight plane for use with Scorpion EVO's that are using the Bullpup Evo Conversion Kit. (It will fit all models of Scorpion EVO in standard configuration including the carbine, pistol, S2 Micro, but the sight plane will typically be too high for most users) .  Weighing in at 18.6 ounces including the mounting block it is only 1.2  ounces heavier than the 12" OEM polymer forend, yet gives an additional 3" of length to completely wrap the barrel or a suppressor and has a built in carry handle.  The forend will clear up to a 1.5" diameter suppressor, and uses an improved mounting block design which free floats the forend from the barrel. The forend comes with the forend, mounting block, and mounting hardwarde.  

    Material: 6061 aluminum

    Finish:  Type III Milspec black hardcoat andozing

    Weight: 18.6 ounces

    Length: 15 inches

    Designed and Manufactured 100% in the USA

    Learn More
  3. Scorpion EVO 15" MLOK Forend
    $179.00

    Out of stock

    The 15" MLOK forend for Scorpion EVO offers no less than 44 slots of M-LOK across its 15" of length along with two integral QD points and will fit all models of Scorpion EVO including the carbine, pistol, S2 Micro, and EVO's using the Bullpup Conversion Kit .  Weighing in at 19.4 ounces including the mounting block it is only 2.0 ounces heavier than the 12" OEM polymer forend, yet gives an additional 3" of length to completely wrap the barrel or a suppressor.  The forend will clear up to a 1.5" diameter suppressor, and uses an improved mounting block design which free floats the forend from the barrel.  The forend comes with the forend, mounting block, and mounting hardwarde.  

    Material: 6061 aluminum

    Finish:  Type III Milspec black hardcoat andozing

    Weight: 19.4 ounces

    Length: 15 inches

    Designed and Manufactured 100% in the USA

    Learn More
  4. Scorpion EVO Angled Transformer Forend

    Regular Price: $134.95

    Special Price $68.00

    Out of stock

    The Scorpion EVO Transformer Forend allows you to use your Scorpion EVO pistol or carbine in a whole new way!

    Learn More
  5. Scorpion EVO Carbine Barrel Nut Tool
    $35.00

    Out of stock

    Use this tool to remove the barrel nut on your CZ Scorpion Carbine. The carbine barrel nut (CZ-USA # 19343) is a standard 21mm hex, problem is that it is buried down inside of the long carbine handguard shroud. This tool acts like a VERY deep socket extension, the clearance inside of the tool allows it to be dropped down over the barrel, and engage the 21mm hex nut that secures the handguard in place.

    Please note that the torque spec for the barrel nut with a factory carbine handguard is 200 in*lbs, or about 16 ft*lbs. Over torquing the barrel nut can cause the factory handguard to crack or split.

    • Barrel Nut Tool for CZ Scorpion Carbine
    • Use with 1/2″ Ratchet or Breaker Bar
    • Made From Chromoly Steel and Zinc coated for corrosion resistance

    Designed and Manufactured completely in USA.

    Gunsmith Installation Recommended for All Parts.

    Learn More
  6. Scorpion EVO Pistol  Barrel Nut Tool
    $12.50

    Out of stock

    Use this tool to remove the barrel nut on your CZ Scorpion Pistol/SBR. The factory barrel nut (#2 on parts diagram) has two flats milled at 20mm. Our tool is designed to engage these flats and through the use of any 1/2″ ratchet or breaker bar remove this stubborn nut. Simply remove the flash hider, then place our tool onto the barrel nut and apply torque to rotate the nut approx 180 degrees, flip the tool, and repeat. Removing the barrel nut provides access to the handguard, barrel, trunnion, sling swivels, and other parts. Tool does NOT fit Scorpion Carbine, and 1/2″ ratchet is not included. 

    • Barrel Nut Tool for CZ Scorpion Pistol/SBR
    • Use with 1/2″ Ratchet or Breaker Bar
    • Made From Chromoly Steel

    Designed and Manufactured completely in USA.

    Gunsmith Installation Recommended for All Parts.

    Learn More
  7. VEPR Keymod Forend  (Closeout)

    Regular Price: $225.00

    Special Price $159.00

    Out of stock

    Made of billet 6061 aluminum and anodizied black, the VEPR forend features a total of 7 rows of Keymod and weighs 12.5 ounces.  The forend replaces the wooden forend found on the original VEPR rifles (will NOT fit a gun that has been modified to use standard AK forends) and uses a screw on the underside to bolt to the gun.  Comes with two spare screws for installation.

    Learn More
  8. X95 Cantilever Forend  ( OEM Height Rail )
    $234.95

    Out of stock

    PLEASE NOTE:  The OEM Height top rail is cut to work with both 5.56 and 300 blackout guns.

    The Patent Pending  X95 Cantilever Forend offers a wealth of features at an incredible price.  To solve some of the inherent issues of how to securely mount a forend to the X95 without contacting the barrel we had to think outside the box, and the solution was a two part system.

    The first component consists of a 39 slot picatinny top rail and cover plate assembly that is matched to the height of the OEM top rail used on the X95.  This is a bit lower than the rail used on guns like the AR-15, but if you find the height of the OEM rail just right you will want to go with this top rail height!  In addition the top rail is cut for the 300 blackout gas adjustment access in case you are mounting on a 300 Blackout X95.

    The second component is the forend itself which is 2" longer than the OEM forend, features 3 rows of M-LOK (13 slots) on each side plus 2 QD points on each side,  and  5 slots of M-LOK on the underside.  The center row of M-LOK on the sides and the underside row on M-LOK is centered on the bore line making it much easier to zero lasers and other items that are bore line sensitive.   The top of the forend features two L-shaped tabs that engage matching slots on the top rail.  To install the forend portion just slide the forend into the slots on the top rail along the axis of the barrel, make sure the alignment tab on the underside engages the opening in the receiver,  tighten the cross bolt screw and you are ready to go with a rock solid mounted forend.  This along-the-bore-axis installation allows the additional benefit of being able to install a suppressor up to 1.5" in diameter on the barrel and the forend can easily be slid on and off without need to remove the suppressor.

    Not wanting to leave an opening where the lower plastic tab of the OEM forend engages, we have included a polymer filler block that blends perfectly with the receiver to keep everything closed up and tidy.

    One last benefit- with X95 Cantilever forend THE BARREL IS NOW FREE FLOATED.  No more contact of the barrel as with the OEM polymer forend and its two barrel mounted polymer support points, as the X95 Cantilever Forend is completely supported by the top rail and the receiver.

    Total weight of the system is 1 lb 3.5 ounces compared to the OEM 1 lb 2.5 ounces.  Only 1.0 ounce more than the OEM forend at a gain of all aluminum construction, the ability to sleeve a suppressor, a longer and higher and more useful top rail, and almost 2" of additional forend with a slimmer profile plus M-LOK compatibility and integral QD points.  Not a bad deal for a single extra ounce, is it?

    The X95 Cantilever Forend  is Patent Pending, and manufactured of 6061 black milspec hardcoated aluminum (plus a polymer filler block) 100% right here in the USA.

    Material:  6061 aluminum and polymer

    Finish:  Type III milspec hardcoat black anodizing 

    Weight:   1 lb 7.4 ounces

    Length:  For 16" and 18.5" barreled guns (2" longer than OEM forend)

    Learn More
  9. X95 Cantilever Forend  ( Taller Height Rail )
    $234.95

    Out of stock

    PLEASE NOTE:  The current product Taller (AR-15 height) Top Rail is cut for the 5.56 caliber guns, but 300 blackout guns will requrie rails with a slight modification.  Manticore Arms will perform this modifaction at no charge, please contact us at info@manticorearms.com prior to purchase.  Future production top rails will work on both 5.56 and 300 blackout guns without modification.

    The Patent Pending  X95 Cantilever Forend offers a wealth of features at an incredible price.  To solve some of the inherent issues of how to securely mount a forend to the X95 without contacting the barrel we had to think outside the box, and the solution was a two part system.

    The first component consists of a 39 slot picatinny top rail and cover plate assembly that is raised to the proper height to work with standard AR-15 iron sights and optics (i.e. most all sighting components on the market these days).  In addition the top rail is cut for the 300 blackout gas adjustment access in case you are mounting on a 300 Blackout X95.

    The second component is the forend itself which is 2" longer than the OEM forend, features 3 rows of M-LOK (13 slots) on each side plus 2 QD points on each side,  and  5 slots of M-LOK on the underside.  The center row of M-LOK on the sides and the underside row on M-LOK is centered on the bore line making it much easier to zero lasers and other items that are bore line sensitive.   The top of the forend features two L-shaped tabs that engage matching slots on the top rail.  To install the forend portion just slide the forend into the slots on the top rail along the axis of the barrel, make sure the alignment tab on the underside engages the opening in the receiver,  tighten the cross bolt screw and you are ready to go with a rock solid mounted forend.  This along-the-bore-axis installation allows the additional benefit of being able to install a suppressor up to 1.5" in diameter on the barrel and the forend can easily be slid on and off without need to remove the suppressor.

    Not wanting to leave an opening where the lower plastic tab of the OEM forend engages, we have included a polymer filler block that blends perfectly with the receiver to keep everything closed up and tidy.

    One last benefit- with X95 Cantilever forend THE BARREL IS NOW FREE FLOATED.  No more contact of the barrel as with the OEM polymer forend and its two barrel mounted polymer support points, as the X95 Cantilever Forend is completely supported by the top rail and the receiver.

    Total weight of the system is 1 lb 7.4 ounces compared to the OEM 1 lb 2.5 ounces.  Only 3.9 ounces more than the OEM forend at a gain of all aluminum construction, the ability to sleeve a suppressor, a longer and higher and more useful top rail, and almost 2" of additional forend with a slimmer profile plus M-LOK compatibility and integral QD points.  Not a bad deal for 3.9 extra ounces, is it?  

    The X95 Cantilever Forend  is Patent Pending, and manufactured of 6061 black milspec hardcoated aluminum (plus a polymer filler block) 100% right here in the USA.

    Material:  6061 aluminum and polymer

    Finish:  Type III milspec hardcoat black anodizing 

    Weight:   1 lb 7.4 ounces

    Length:  For 16" and 18.5" barreled guns (2" longer than OEM forend)

    100% designed and manufactured in the USA

    Learn More

Grid List

Set Descending Direction

11-19 of 19

Page:
  1. 1
  2. 2