FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Shop All

Shop All

Grid List

Set Ascending Direction

1-10 of 81

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  1. Yugo Krinkov NightBrake 26mm
    $64.95

    Machined from 8620 steel with a black oxide finish and heat treated for a life of hard use, the Manticore Arms Yugo M92 NightBrake muzzle compensator is designed specifically for the 26x1.5 left hand thread found on the muzzle of the Yugoslavian M92 and M85 Krinkov rifles and PAP series of pistols. The NightBrake is designed to reduce felt recoil, virtually eliminate muzzle rise, and can safely pass any projectile up to 0.311" (0.30 caliber) in diameter, making it a universal muzzle device for both the M85 and M92. A total of eighteen ports distributed around the upper 270-degree arc of the device help stabilize and reduce exiting gas pressure, and the lower 90-degree arc has no ports to prevent a dust signature when fired.

    The Yugo M92 NightBrake flash hider is 2.125 inches long, adding only 1.125 inches to the overall length of the rifle- it is over an inch shorter than the standard M92 muzzle booster. In addition the weight is only 3.0 ounces, and it is marked "MANTICORE" to denote a U.S. made part that counts towards 922r compliance.

    Material:  8620 steel with heat treat

    Finish:  Black oxide

    Weight:  2.7 ounces

    Length:  2.125 inches

    100% designed and manfuactured in the USA

    Learn More
  2. Yugo Front Detent Kit (for Yugo M92 and M85 PAP)
    $12.95

    You may have discovered when removing the thread protector collar on your Yugo PAP pistol that there isn’t a front sight detent pin to hold your muzzle device in place. This part is the correct replacement for that missing pin.

    Manufactured from 4140 steel with a black oxide finish, the Yugo Front Detent Kit includes the detent pin, a spring, and a roll pin. Simply place the spring on the back of the detent pin, insert in the hole located in the front sight base, push in slightly against the spring pressure and tap in the roll pin. The Yugo Front Detent Kit is manufactured here in the U.S.A. and is the perfect addition to the Yugo M92 NightShroud or Yugo M92 NightBrake.

    Material:  4140 steel

    Finish:  Black oxide

    Weight:

    Length:  N/A

    Learn More
  3. X95 Switchback Charging Handle
    $83.95

    Please note: The X95 Switchback Charging Handle does not fit the Tavor SAR.

    Please Note:  You may see some coesmetic burnishing of the polymer where the charging handle rides on the slot.  This is completely normal, willnot harm the rifle, and also happens with the OEM charging handle.  I fyou are not comfortable with this cosmetic burnishing please do not purchase this product.

    The X95 Switchback is a folding charging handle that will work on either side of the X95. It offers the lowest possible profile when folded but a good two finger grip when deployed. The handle is folded out by hand, pulled back comfortably, and then released. The force of the handle going forward will cause it to flip forward, i.e. "switch back" to the stowage position and lock there via a spring loaded detent and small tab on the handle.  A 45 degree front face allows you to sweep the hand back to "find" the handle and deploy and pullin one single, smooth motion.

    The X95 Switchback is made in the USA of 6061 aluminum that is anodized black, and consists of a folding handle and lug with a steel rod, all of which are preassembled. The X95  Switchback not only can be mounted on either side of the X95 but with a small modification to the inner plastic gas cover it is possible to run two handles on the rifle at the same time.

    The X95 Switchback will work with both the OEM forends (both 16" and 13" SBR length) and with the Manticore X95 Cantilever Forend.

    Material:  6061 aluminum handle and steel rod

    Finish:  Type III milspec hardcoat black anodizing on aluminum and black oxide on steel

    Weight:  2.5  ounces

    Length:  N/A

    100% designed and manufactured in the USA

    Learn More
  4. X95 Curved Buttpad (for X95 Tavor)
    $72.95

    PLEASE NOTE THIS BUTTPAD WILL ONLY FIT THE  X95 TAVOR AND NOT THE ORIGINAL TAVOR SAR

    Similar to our Tavor Curved Buttpad, the X95 Curved Buttpad features an aluminum skeleton structure with an overmolded rubber pad.  The rubber pad is curved to conform to the shoulder and not only give better ergonomics and grip but also shortens the overall length of pull on the rifle.  By keeping the top edge the same length as the OEM buttpad the rifle does not drop under 26" inches in length, which if shorter than that would make it an NFA Short Barreled Rifle.

    The X95 curved buttpad is made by Manticore Arms in the USA.

     Please note that Tavor Curved Buttpads and X95 Curved Buttpads ARE NOT interchangeable- each model of IWI Tavor uses its own dedicated buttpad.  Please be sure to order the correct buttpad for your rifle, and if not sure please contact customer service at info@manticorearms.com

     

    Material: 6061 aluminum and rubber like polymer

    Finish:  Black Cerakote on aluminum, black finish on rubber like polymer

    Weight: 6.5 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  5. X95  SBR  Cantilever Forend  ( OEM Height Rail) GEN II
    $234.95

     PLEASE NOTE:  The AR-15 Height top rail is cut to work with all calibers of Tavor X95.

    The X95 SBR Cantilever Forend offers a wealth of features at an incredible price.  To solve some of the inherent issues of how to securely mount a forend to the X95 without contacting the barrel we had to think outside the box, and the solution was a two part system.

    The first component consists of a 30 slot picatinny top rail and cover plate assembly that is the same height as the OEM top rail found on the X95. In addition the top rail is cut for the 300 blackout gas adjustment access in case you are mounting on a 300 Blackout X95.

    The second component is the forend itself which is 4.57" long from front to rear, ideal for the 13" SBR barrel, but will work with any length and caliber of barrel , features 3 rows of M-LOK (5 full slots and two partial slots) on each side plus one QD points on each side,  and  2 full and one partial slots of M-LOK on the underside.  The center row of M-LOK on the sides and the underside row on M-LOK is centered on the bore line making it much easier to zero lasers and other items that are bore line sensitive.   The top of the forend features two L-shaped tabs that engage matching slots on the top rail.  To install the forend portion just slide the forend into the slots on the top rail along the axis of the barrel, make sure the alignment tab on the underside engages the opening in the receiver,  tighten the cross bolt screw and you are ready to go with a rock solid mounted forend.  This along-the-bore-axis installation allows the additional benefit of being able to install a suppressor up to 1.5" in diameter on the barrel and the forend can easily be slid on and off without need to remove the suppressor.

    Not wanting to leave an opening where the lower plastic tab of the OEM forend engages, we have included a polymer filler block that blends perfectly with the receiver to keep everything closed up and tidy. The forend and top rail are connected via a tongue and groove rail system and are secured together with screws for stable mounting and no movement.

    One last benefit- with X95 SBR Cantilever forend THE BARREL IS NOW FREE FLOATED.  No more contact of the barrel as with the OEM polymer forend and its two barrel mounted polymer support points, as the X95 SBR Cantilever Forend is completely supported by the top rail and the receiver.

    Total weight of the system is 13.5 ounces.

    The X95 Cantilever Forend  is Patent Pending, and manufactured of 6061 black milspec hardcoated aluminum (plus a polymer filler block) 100% right here in the USA.

    Material:  6061 aluminum and polymer

    Finish:  Type III milspec hardcoat black anodizing 

    Weight:   15.5 ounces

    Length:  For  13" SBR barrels, will also work with 16" and 18.5" barreled guns 

    100% designed and manufactured in the USA

     

    Learn More
  6. X95  SBR  Cantilever Forend  ( AR-15 Height Rail) GEN II
    $234.95

     PLEASE NOTE:  The AR-15 Height top rail is cut to work with all calibers of Tavor X95.

    The X95 SBR Cantilever Forend offers a wealth of features at an incredible price.  To solve some of the inherent issues of how to securely mount a forend to the X95 without contacting the barrel we had to think outside the box, and the solution was a two part system.

    The first component consists of a 29 slot picatinny top rail and cover plate assembly that is raised to the proper height to work with standard AR-15 iron sights and optics (i.e. most all sighting components on the market these days). In addition the top rail is cut for the 300 blackout gas adjustment access in case you are mounting on a 300 Blackout X95.

    The second component is the forend itself which is 4.57" long from front to rear, ideal for the 13" SBR barrel, but will work with any length and caliber of barrel , features 3 rows of M-LOK (5 full slots and two partial slots) on each side plus one QD points on each side,  and  2 full and one partial slots of M-LOK on the underside.  The center row of M-LOK on the sides and the underside row on M-LOK is centered on the bore line making it much easier to zero lasers and other items that are bore line sensitive.   The top of the forend features two L-shaped tabs that engage matching slots on the top rail.  To install the forend portion just slide the forend into the slots on the top rail along the axis of the barrel, make sure the alignment tab on the underside engages the opening in the receiver,  tighten the cross bolt screw and you are ready to go with a rock solid mounted forend.  This along-the-bore-axis installation allows the additional benefit of being able to install a suppressor up to 1.5" in diameter on the barrel and the forend can easily be slid on and off without need to remove the suppressor.

    Not wanting to leave an opening where the lower plastic tab of the OEM forend engages, we have included a polymer filler block that blends perfectly with the receiver to keep everything closed up and tidy. The forend and top rail are connected via a tongue and groove rail system and are secured together with screws for stable mounting and no movement.

    One last benefit- with X95 SBR Cantilever forend THE BARREL IS NOW FREE FLOATED.  No more contact of the barrel as with the OEM polymer forend and its two barrel mounted polymer support points, as the X95 SBR Cantilever Forend is completely supported by the top rail and the receiver.

    Total weight of the system is 15.5 ounces.

    The X95 Cantilever Forend  is Patent Pending, and manufactured of 6061 black milspec hardcoated aluminum (plus a polymer filler block) 100% right here in the USA.

    Material:  6061 aluminum and polymer

    Finish:  Type III milspec hardcoat black anodizing 

    Weight:   15.5 ounces

    Length:  For  13" SBR barrels, will also work with 16" and 18.5" barreled guns 

    100% designed and manufactured in the USA

     

    Learn More
  7. Triangle Stock
    $112.95

    Please note, no hinge or mounting block is included, these can be purchase at stormwerkz.com or a variety of other suppliers.

    The Triangle Stock bolts to any standard 10-32 bolt pattern stock adapter or hinge, such as those offered by Stormwerkz and ACE Riflestocks.  It is easily adapted to any AK, and can even be mounted to a Yugo PAP pistol by simply drilling and tapping two 10-32 holes in the rear trunnion (make sure the pistol is registered as an SBR before doing this.)

    Made of 6061 aluminum that is bead blasted and anodized black, the stock weighs only 10.0 ounces as the arms and rear of the stock are now scallop cut internally to reduce weight, and with a hinge installed will have the exact length of a true Russian or Bulgarian sidefolder stock. The rear of the stock has a machined rib pattern to give a good grip on the shoulder, and with the use of a hinge it can be configured to fold left or right. The Triangle Stock comes with the stock, two 10-32 bolts and washers. Overall LOP (Length Of Pull from buttplate to face of trigger) with Triangle Stock and Stormwerkz or Ace Riflestock Hinge installed is 12.25", exactly the same LOP as a real Russian or Bulgarian Sidefolder AK.

    Material: 6061 aluminum

    Finish: Type III milspec hardcoat black anodizing

    Weight: 11.0 ounces

    Length: 8.5 inches (stock only not including hinge or mounting blocks)

    100% designed and manufactured in the USA

    Learn More
  8. Tavor TS12 Shotgun Curved Buttpad
    $72.95

    PLEASE NOTE THIS BUTTPAD WILL ONLY FIT THE  TAVOR TS12 SHOTGUN.  IT WILL NOT FIT THE TAVOR SAR, TAVOR X95, OR TAVOR 7

    Similar to our Tavor Curved Buttpad, the Tavor TS12 Shotgun Curved Buttpad features an aluminum skeleton structure with an overmolded rubber pad.  The rubber pad is curved to conform to the shoulder and gives both better ergonomics and a better grip so the rifle does not slide around, and has an additoinal 1" of "drop" at the toe over the OEM buttpad to give a much larger surface area and the ability to ride the shotgun higher on the shoulder for a more inline stance.

    The Tavor TS12 Shotgun Curved Buttpad is made by Manticore Arms in the USA.

     Please be sure to order the correct buttpad for your rifle, and if not sure please contact customer service at info@manticorearms.com

     

    Material: 6061 aluminum and rubber like polymer

    Finish:  Black Cerakote on aluminum, black finish on rubber like polymer

    Weight: 11.4 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  9. Tavor TS12 Knurled Charging Handle
    $38.95

    The Tavor TS12 Knurled Charging handle projects out 1/4" farther than the OEM handle and has a 1/2" diameter knurled drum for good purchase, and  we have found this to be the perfect size to give a good grip without racking knuckles on the receiver yet the handle does not project out too far from the side of the gun.

    Just like the OEM handle the Knurled Charging Handle will work on both the left and right side of the gun and is a drop in replacement made 100% in the USA.

    Material: 1018 Steel

    Finish:  Black oxide

    Weight:  1.4 ounces

    Length:  N/A

    100% designed and manufactured in the USA

    Learn More
  10. Tavor Switchback Charging Handle
    $83.95

    Please note: The Tavor Switchback Charging Handle does not fit the X95.

    The Tavor Switchback is a folding charging handle that will work on either side of the Tavor. It offers the lowest possible profile when folded but a good two finger grip when deployed. The handle is folded out by hand, pulled back, and then released. The force of the handle going forward will cause it to flip forward, i.e. "switch back" to the stowage position and lock there via a spring loaded detent and small tab on the handle. The Tavor Switchbackconsists of an inner lug and rod assembly and an outer handle assemble which are attached by two screws and includes the componets, hardware, allen wrench, and instruction sheet necessary for installation. The Tavor Switchback not only can be mounted on either side of the Tavor but with a small modification to the inner plastic gas cover it is possible to run two handles on the rifle at the same time.

    Material: 6061 aluminum and steel rod

    Finish:  Type III milspec hardcoat black anodizing on aluminum and black oxide on steel

    Weight: 3.4 ounces

    Length: N/A

    Designed and Manufactured 100% in the USA

    Learn More

Grid List

Set Ascending Direction

1-10 of 81

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5