FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Shop All

Shop All

Grid List

Set Ascending Direction

21-30 of 77

  1. Scorpion EVO Bench Block
    $67.95

    The Bench Block is made of a heavy duty blue polymer that will not mar the surface of the receiver, and is shaped to fully support and distribute loads on the Scorpion EVO receiver while working on the gun. Four included bolts with nuts and washers are used to "clamshell" the receiver with the two blocks, and then the blocks, instead of the receiver, can be clamped into a vise to do work on the gun. An instruction sheet for proper use of the block is included.

    Please note that the OEM barrel nut is typically installed with thread locker, and that heat should be applied with a heat gun or carefully with a propane torch to break down the thread locker prior to trying to remove the barrel nut, even when using the Bench Block. We have seen some nuts come off with almost no force, and some require very high amounts of force to break them loose.

    If in doubt, take the gun to a Gunsmith to have the work done. Due to the inconsistent amount of thread locker used by CZ on the barrel nut Manticore Arms cannot be held liable for damage to the gun or components of the gun even when using the Bench Block.

    Material: Polymer

    Finish:  Black oxide

    Weight: 1 lb 4.0 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  2. Scorpion EVO 15" MLOK Forend
    $178.95

    The 15" MLOK forend for Scorpion EVO offers no less than 44 slots of M-LOK across its 15" of length along with two integral QD points and will fit all models of Scorpion EVO including the carbine, pistol, S2 Micro, and EVO's using the Bullpup Conversion Kit .  Weighing in at 19.4 ounces including the mounting block it is only 2.0 ounces heavier than the 12" OEM polymer forend, yet gives an additional 3" of length to completely wrap the barrel or a suppressor.  The forend will clear up to a 1.5" diameter suppressor, and uses an improved mounting block design which free floats the forend from the barrel.  The forend comes with the forend, mounting block, and mounting hardwarde.  

    Material: 6061 aluminum

    Finish:  Type III Milspec black hardcoat andozing

    Weight: 19.4 ounces

    Length: 15 inches

    Designed and Manufactured 100% in the USA

    Learn More
  3. Scorpion EVO 15" Carry Handle MLOK Forend
    $229.95

    PLEASE NOTE:  THIS FOREND IS ONLY RECOMMENDED FOR USE WITH A SCORPION EVO THAT HAS THE BULLPUP CONVERSION KIT INSTALLED.  THE SIGHT PLANE OF THE CARRY HANDLE WILL BE TOO HIGH FOR MOST USERS WHEN MOUNTED ON A STANDARD SCORPION EVO.

    The 15" Carry handle MLOK forend for Scorpion EVO offers no less than 49 slots of M-LOK across its 15" of length along with two integral QD points and is designed specifically to give a higher sight plane for use with Scorpion EVO's that are using the Bullpup Evo Conversion Kit. (It will fit all models of Scorpion EVO in standard configuration including the carbine, pistol, S2 Micro, but the sight plane will typically be too high for most users) .  Weighing in at 18.6 ounces including the mounting block it is only 1.2  ounces heavier than the 12" OEM polymer forend, yet gives an additional 3" of length to completely wrap the barrel or a suppressor and has a built in carry handle.  The forend will clear up to a 1.5" diameter suppressor, and uses an improved mounting block design which free floats the forend from the barrel. The forend comes with the forend, mounting block, and mounting hardwarde.  

    Material: 6061 aluminum

    Finish:  Type III Milspec black hardcoat andozing

    Weight: 18.6 ounces

    Length: 15 inches

    Designed and Manufactured 100% in the USA

    Learn More
  4. Scorpion EVO 12" MLOK Forend
    $158.95

    The 12" MLOK forend for Scorpion EVO offers no less than 27 slots of M-LOK across its 12" of length along with two integral QD points and will fit all models of Scorpion EVO including the carbine, pistol, S2 Micro, and EVO's using the Bullpup Conversion Kit .  Weighing in at 14.7 ounces including the mounting block it is actually 2.7 ounces lighter than the 12" OEM polymer forend.  The forend will clear up to a 1.5" diameter suppressor, and uses an improved mounting block design which free floats the forend from the barrel.  The forend comes with the forend, mounting block, and mounting hardwarde.  

    Material: 6061 aluminum

    Finish:  Type III Milspec black hardcoat andozing

    Weight: 14.7 ounces

    Length: 12 inches

    Designed and Manufactured 100% in the USA

    Learn More
  5. Scorpion EVO 12" Carry Handle MLOK Forend
    $208.95

    PLEASE NOTE:  THIS FOREND IS ONLY RECOMMENDED FOR USE WITH A SCORPION EVO THAT HAS THE BULLPUP CONVERSION KIT INSTALLED.  THE SIGHT PLANE OF THE CARRY HANDLE WILL BE TOO HIGH FOR MOST USERS WHEN MOUNTED ON A STANDARD SCORPION EVO.

    The 12" Carry handle MLOK forend for Scorpion EVO offers no less than 23 slots of M-LOK across its 12" of length along with two integral QD points and is designed specifically to give a higher sight plane for use with Scorpion EVO's that are using the Bullpup Evo Conversion Kit. (It will fit all models of Scorpion EVO in standard configuration including the carbine, pistol, S2 Micro, but the sight plane will typically be too high for most users) .  Weighing in at 16.9 ounces including the mounting block it is actaully 0.5 ounces lighter than the 12" OEM polymer forend and has a built in carry handle to boot.  The forend will clear up to a 1.5" diameter suppressor, and uses an improved mounting block design which free floats the forend from the barrel. The forend comes with the forend, mounting block, and mounting hardware.  

    Material: 6061 aluminum

    Finish:  Type III Milspec black hardcoat andozing

    Weight: 16.9 ounces

    Length: 12 inches

    Designed and Manufactured 100% in the USA

    Learn More
  6. Scorpion EVO  Slider Stock
    $257.95

    Inspired by the looks and function of the MP5A3 telescoping stock, the Scorpion EVO Slider Stock when fully collapsed only adds 3/4" of length and no additional width to the gun. The stock will friction lock at the closed position and can be "quick pulled" for instant deployment and will lock in the open position. Maximum length of pull is 12.5"  and the gun can be fired with the stock open or even fully collapsed with no interference of the ejection port. The stock features a QD point on the mounting block left side and also a QD point on the top of the buttplate along with a sling loop on the underside of the buttplate. The buttplate is grooved for a good grip on the shoulder, and has the ability to mount an optional rubber buttpad if the user prefers.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 12.0 ounces

    Length: 9.125"

    100% designed and manufactured in the USA

    Learn More
  7. Reverb Muzzle Brake 1/2 x 28 tpi
    $43.95

    The Reverb Muzzle Brake is a compact muzzle compensator that will work with any round under 9mm in diameter (i.e. 300 Blackout, 5.56mm, etc) on 1/2 x 28 tpi threaded barrels.

    Learn More
  8. Renegade Optics Mount Top Cover - Yugo AK

    The Optics Mount Top Plate is the perfect compliment the Renegade forearm, and the top plate bolts securely onto the gas tube and allows mounting of various optics in a co-witness plane. Multiple models are available including the Burris Fastfire top, Picatinny top plate and the Aimpoint Micro/Primary Arms Micro top plate. FOUR OPTIONS ARE AVAILABLE:

    1. Aimpoint Micro/Primary Arms top plate: Works with Aimpoint Micro and most Aimpoint Micro Clones including the Primary Arms model MD-ADS and MD-RBGII.

    2. Burris Fastfire top plate: Works with the Burris Fastfire

    3. Picatinny top plate: Includes the Burris Fastfire top cover and a bolt on 5 slot picatinny rail segment which attaches to the Burris Fastfire top plate and allows you to mount any picatinny based optic. Please note that you will not be able to co-witness with the iron sights when using the picatinny rail and mount.

    4. Picatinny rail only: Just the picatinny rail segment that can mount to the top of the Burris Fastfire top plate (for those who already have a Burris Fastfire top plate and wish to mount a picatinny based optic)

    The Optics Mount Top Plate for Yugo AK will fit all models of Yugo M92 and M85 PAP pistol and rifle, and is proudly made in the USA. Optics Mount Top Plates are made of 6061 anodized aluminum and come with the top plate, two "U" mounting brackets, 6-32 screws, allen wrench, and instructions for installation and are proudly made in the USA. Optics Mount Top Plates are only intended to be used with the Renegade polymer lower forearm. THE OPTICS MOUNT TOP COVER SHOULD NOT BE USED ALONE, IT SHOULD ONLY BE USED WITH THE RENEGADE FOREARM. OPTICS MOUNT TOP COVERS ARE ONLY AVAILABLE SEPARATELY FOR THOSE WHO HAVE ALREADY PURCHASED THE POLYMER LOWER!

    Material:  6061 aluminum

    Finish:  Type III hardcoat milspec black anodizing

    Weight: 2.0 ounces

    Length:  Renegade forend only

    Learn More
  9. Renegade Handguard Assembly For Yugo M85 and M92
    $44.95

    The Renegade Forearm with Polymer Top Cover for Yugo Krink AK offers full protection of the fore end of the rifle with a high temperature thermoset polymer. The forearm features a a "bulged U" cross section giving greater ergonomics and blends perfectly into the front of the receiver unlike most other fore ends available.

    The forearm has texturing grooves at the gripping surface, and not one but two rows of ARClight slots on each side and even a row underneath that allow attachment of Manticore Arms ARC LOK rail segments, and even attachment of Magpul MOE series polymer rail segments and Impact Weapon Components Mount-N-Slot accessories.

    To compliment the Renegade forearm the top plate bolts securely onto the gas tube and allows mounting of various optics in a co-witness plane. Multiple models are available including the Burris Fastfire top plate and the Aimpoint Micro/Primary Arms Micro top plate. The Renegade forearm for Yugo AK will fit all models of Yugo M92 and M85 PAP pistol and rifle, and is proudly made in the USA. Optics Mount Top Plates are made of 6061 anodized aluminum and come with the top plate, two "U" mounting brackets, 6-32 screws, allen wrench, and instructions for installation and are proudly made in the USA. Optics Mount Top Plates are only intended to be used with the Renegade polymer lower forearm.

    Colors are a prefect match to Magpul Black, FDE, and Russian Plum Colors.  Bakelite Orange is a match to authentic bakelite AK-47 magazines and to Tapco Orange.

    Material:  Polymer

    Finish:  Multiple colors

    Weight: 5.6 ounces

    Length:  Standard Yugo M85 and M92 PAP forend

    100% designed and manufactured in the USA

    Learn More
  10. Renegade Forearm Polymer Top Cover
    $15.00

    Out of stock

    The Renegade Polymer Top Cover allows you to close up the upper portion of the Renegade for a completed look when you do not need to mount an optic up front.

    Made of the same high temperature thermoset polymer as the Renegade Forend, and featuring a grooved surface to match the aesthetics of the lower it is the perfect way to get the full Renegade look on your Yugo PAP.

    The Renegade Polymer Top Cover will fit all models of Yugo M92 and M85 PAP pistol and rifle, and is proudly made in the USA. Please note this part is only meant to be used with the Renegade Forend, and is not compatible with other forends for the Yugo PAP pistol.

    Material:  Polymer

    Finish:  Various Colors

    Weight: ??

    Length:  Only for use with Renegade Forend

    Learn More

Grid List

Set Ascending Direction

21-30 of 77