FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Shop All

Shop All

Grid List

Set Descending Direction

1-10 of 79

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  1. 13"  GEN II Transformer Rail for AR-15
    $154.95

    Your rail now automatically ships with (6)  Snakeskin polymer grip panels at not charge!

    GEN II barrel nut design is lighter, simpler, and easier to install!  Just torque to the recommend barrel nut torque setting, slide rail over and install 8 set screws and you are done!  No need to time barrel nut or align threaded holes, plus a cleaner look than the original Transformer Rail!

     M-LOK and Keymod....ON THE SAME RAIL!

    The Transformer Rail comes with the rail, barrel nut, barrel nut wrench, and six polymer grip panels.  Additional panels available in pulldown menus!

    Specifications:

    • AR-15 Aluminum Free Float rail system with ability to intermix Keymod, M-LOK, and polymer grip panels

    • Dimensions: 13” length, 1.5” exterior width, 1.09” interior clear width

    • Weight: 7.4 ounces for rail, 1.5 ounces for barrel nut, under 0.3 ounces per panel

    • Weight installed: 8.9 ounces (only adds 7.4 ounces as original barrel nut is removed)

    • Barrel nut material and finish: 6061 6061 T6 aluminum with Milspec Type III Black hardcoat anodizing

    • Rail material and finish: 6061 T6 aluminum with Milspec Type III Black hardcoat anodizing

    • Panel material and finish: 6061 black anodized aluminum and proprietary polymer 

    • Ships with Transformer Rail, Barrel Nut, Barrel Nut Wrench, all hardware, 6 polymer grip panels, allen wrenches, and instruction sheet

    • Interchangeable Transformer panel system allows for mixing of Keymod, M-LOK, and polymer grip panels. Other panels, such as Picatinny, will launch after initial release

    • Six Transformer panel mounting locations

    • GEN II barrel nut design is lighter, simpler, and easier to install!  Just torque to the recommend barrel nut torque setting, slide rail over and install 8 set screws and you are done!  No need to time barrel nut or align threaded holes, plus a cleaner look than the original Transformer Rail!

    • Eight QD sling swivel pockets- three on each side and two underneath

    • Clears low profile gas blocks and works with all gas system lengths (carbine, midlength, rifle)

    • 100% Designed and Made in the USA

    • Multiple Patents Pending

    Learn More
  2. 15"  GEN II Transformer Rail for AR-15
    $164.95

    Your rail now automatically ships with (6)  Snakeskin polymer grip panels at no charge!

    GEN II barrel nut design is lighter, simpler, and easier to install!  Just torque to the recommend barrel nut torque setting, slide rail over and install 8 set screws and you are done!  No need to time barrel nut or align threaded holes, plus a cleaner look than the original Transformer Rail!

     M-LOK and Keymod....ON THE SAME RAIL!

    The Transformer Rail comes with the rail, barrel nut, barrel nut wrench, and six polymer grip panels.  Additional types of panels can be added below!

    Specifications:

    • AR-15 Aluminum Free Float rail system with ability to intermix Keymod, M-LOK, and polymer grip panels

    • Dimensions: 15” length, 1.5” exterior width, 1.09” interior clear width

    • Weight: 8.4 ounces for rail, 1.5 ounces for barrel nut, under 0.3 ounces per panel

    • Weight installed: 9.9 ounces (only adds 7.4 ounces as original barrel nut is removed)

    • Barrel nut material and finish: 6061 6061 T6 aluminum with Milspec Type III Black hardcoat anodizing

    • Rail material and finish: 6061 T6 aluminum with Milspec Type III Black hardcoat anodizing

    • Panel material and finish: 6061 black anodized aluminum and proprietary polymer 

    • Ships with Transformer Rail, Barrel Nut, Barrel Nut Wrench, all hardware, 6 polymer grip panels, allen wrenches, and instruction sheet

    • Interchangeable Transformer panel system allows for mixing of Keymod, M-LOK, and polymer grip panels. Other panels, such as Picatinny, will launch after initial release

    • Six Transformer panel mounting locations

    • GEN II barrel nut design is lighter, simpler, and easier to install!  Just torque to the recommend barrel nut torque setting, slide rail over and install 8 set screws and you are done!  No need to time barrel nut or align threaded holes, plus a cleaner look than the original Transformer Rail!

    • Eight QD sling swivel pockets- three on each side and two underneath

    • Clears low profile gas blocks and works with all gas system lengths (carbine, midlength, rifle)

    • 100% Designed and Made in the USA

    • Multiple Patents Pending

    Learn More
  3. 15"  MLOK Rail for AR-15
    $164.95

    Specifications:

    • AR-15 Aluminum Free Float rail system with M-LOK slots on sides and underside, picatinny on top.

    • Dimensions: 15” length, 1.5” exterior width, 1.09” interior clear width

    • Weight: 8.4 ounces for rail, 1.5 ounces for barrel nut

    • Weight installed: 9.9 ounces (only adds 7.4 ounces as original barrel nut is removed)

    • Barrel nut material and finish: 6061 6061 T6 aluminum with Milspec Type III Black hardcoat anodizing

    • Rail material and finish: 6061 T6 aluminum with  Milspec Type III Black hardcoat anodizing

    • Panel material and finish: 6061 black anodized aluminum and proprietary polymer 

    • Ships with M-LOK Rail, Barrel Nut, Barrel Nut Wrench, all hardware, allen wrenches, and instruction sheet

    • The Manticore GEN II barrel nut design is lighter, simpler, and easier to install!  Just torque to the recommend barrel nut torque setting, slide rail over and install 8 set screws and you are done!  No need to time barrel nut or align threaded holes, plus a cleaner look!

    • Clears low profile gas blocks and works with all gas system lengths (carbine, midlength, rifle)

    • 100% Designed and Made in the USA

    Learn More
  4. 3X QD Sling Mount Picatinny
    $25.95

    The 3X QD Sling Mount (Picatinny)  provides a simple yet very durable mounting point for QD pockets on and picatinny rail, and allows for mounting QD sling swivels in three different positions. Ideal for use on top of a rail system to give left, right, and to mounting options, it will mount to any picatinny surface giving you a host of flexibility for setting up a sling. The 3X QD Sling Mount (Picatinny) is made of black anodized 6061 aluminum, mounts and secures with a crossbolt, and is 100% made in the USA.

    Material:  6061 aluminum  

    Finish:  Type III hardcoat milspec black anodizing   

    Weight:  0.8 ounces   

    Length:  N/A   

    100% designed and manufactured in the USA

    Learn More
  5. Afterburner Flash Hider Tip
    $28.95

    Tailor the performance of your Afterburner Linear Compensator to your exact needs with our thread-on muzzle tips. The Afterburner Flash Hider Tip adds only 1 ounce and 0.625 inches of length to the Afterburner Linear Compensator, amd dials it in to reduce flash signature. The tip installs via the internal threads in the front of the Afterburner.  No thread locker or washers are necessary to install the tip, just thread it in snugly and it is secure.

    Material:  8620 steel with heat treat

    Finish:  Black oxide

    Weight:  1.0 ounces

    Length:  0.625"  past face of Afterburner Muzzle

    100% designed and manufactured in the USA

    Learn More
  6. Afterburner Linear Compensator 1/2x28 tpi
    $43.95

    The Afterburner Linear Compensator is one of the slimmest linear compensators on the market, yet is designed to give the same performance of larger "fatty" linear comps made by other companies. Measuring 1.00 inches in diameter and 2.25 inches in length with a 1.80 inch long inner chamber, the Afterburner features internal threading which serves dual purposes: distributing gas flow to reduce flash and provide a threaded surface where optional threaded muzzle ends, such as flash hider and compensator tips, can be added on for additional effect. The Afterburner will fit inside the Manticore Arms AR-15 Transformer Forend. The Afterburner Linear Compensator is marked "MA" and "USA" to denote 922r compliance and includes a crush washer and has wrench flats for ease of installation

    Material: 8620 steel with Rockwell 50C heat treat

    Finish:  Black oxide

    Weight: 3.4 ounces

    Length: 2.25 inches

    100% designed and manufactured in the USA

    Learn More
  7. ALFA RAIL Keymod Forend for stamped AK
    $118.95

    PLEASE NOTE: THE ALFA LOWER FOREND OPTION FOR $119 IS ONLY THE LOWER PORTION, THE UPPER HANDGARD IS NOT INCLUDED WITH THIS OPTION! THE MA-11275 ALFA HANDGUARD WILL ONLY FIT STANDARD STAMPED 'EURO' AND 'CHINESE' AK'S.

    THIS MODEL WILL NOT FIT YUGO M-70/N-PAP/O-PAP, KRINKOVS, M92'S, UNCONVENRTED VEPR'S OR UNCONVERTED SAIGAS.

    The ALFA RAIL Keymod forend for the standard pattern AK gives the look and feel of a more traditional AK forend while giving the ability to mount Keymod accessories and other optional components, all while mounting exactly like the original handguard.

    The forend is simply installed like any standard AK handguard and is held in place by the front handguard retainer. An extremely precise and tight fight, in addition to careful design of the interface points with weapon ensures that the mounting is rock solid.

    Weighing 3.5 ounces it is actually almost an ounce lighter than the original polymer forend, yet several times stronger. An optional Superlow Optics Mount Upper which weighs only 2 ounces allows you to mount an Aimpoint Micro on its picatinny top rail and have co-witness with the iron sights.

    The ALFA RAIL lower forend will work with the standard polymer or wood upper handguard, or even with an Ultimak railed upper gas tube. Manufactured from solid billets of 6061 T6 aluminum and anodized black the ALFA RAIL upper and lower include instructions and all hardware necessary for installation and are 100% made in the USA.

    Material: 6061 aluminum

    Finish: Type III Milspec Hardcoat Black Anodizing

    Weight: 3.5 ounces lower rail, 2.0 ounces optional top cover

    Length: Standard AK forend

    100% designed and manufactured in the USA.

    Learn More
  8. ARClight ARC LOK aluminum rail segments
    $23.00

    Available in either 5 slots and 11 slot lengths, the ARClight ARC LOK rail segments are designed specifically to attach to all ARClight forearm and rail systems.

    Made from 6061 aluminum and anodized black, the rail segments are attached through our patent pending ARC LOK rotating tabs- there is no need to be able to access the back side of the mounting surface, just insert the rail segment, rotate the screws 2-3 turns counterclockwise, then rotate clockwise until tight and it is attached!

    Lugs on the back of the rail interface with the ARClight slots and transfer the forces directly to the ARClight forearm or rail system, instead of through the screws like most other attachable rail systems. ARClight rail segments are made in the USA and come with steel backer bar, mounting screws, and an allen wrench for easy installation.

    Material:  6061 Aluminum

    Finish: Type III Hardcoat Milspec Anodizing

    Wieght: ??

    Length: ??

    Learn More
  9. ARClight Pathfinder Tavor Forend
    $199.95

    ***PLEASE NOTE THIS IS A SPECIAL RUN WITH LIMITED QUANTITIES***

    The Pathfinder is a direct replacement for the OEM polymer Tavor SAR forend, is 7 inches longer than the OEM forend, and is intended to act as heat protection against a suppressor that is mounted to the barrel. The monolithic design allows it to sleeve over any suppressor up to 1.75" in diameter, and most suppressors will have approximately one inch visible out the front of the forend. ARC LOK slots on the entire surface let you mount any combination of accessories and grip further out on the gun, including on top of the front of the forend. It is made of completely monolithic construction, with no welds or fasteners to fail.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 13.4 ounces

    Length: ?? inches

    Designed and Manufactured 100% in the USA

    Learn More
  10. ARClight Tavor Cover Plate
    $27.95

    The Cover Plate allows you to close off the front end of the ARClight and ARClight XTL forend for when you do not want to mount a light internally. The Cover Plate is made from black anodized 6061 aluminum and is made in the USA. It includes all necessary hardware for mounting. Learn More

Grid List

Set Descending Direction

1-10 of 79

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5