FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Shop All

Shop All

Grid List

Set Descending Direction

1-10 of 11

Page:
  1. 1
  2. 2
  1. ARClight Pathfinder Tavor Forend
    $199.95

    ***PLEASE NOTE THIS IS A SPECIAL RUN WITH LIMITED QUANTITIES***

    The Pathfinder is a direct replacement for the OEM polymer Tavor SAR forend, is 7 inches longer than the OEM forend, and is intended to act as heat protection against a suppressor that is mounted to the barrel. The monolithic design allows it to sleeve over any suppressor up to 1.75" in diameter, and most suppressors will have approximately one inch visible out the front of the forend. ARC LOK slots on the entire surface let you mount any combination of accessories and grip further out on the gun, including on top of the front of the forend. It is made of completely monolithic construction, with no welds or fasteners to fail.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 13.4 ounces

    Length: ?? inches

    Designed and Manufactured 100% in the USA

    Learn More
  2. ARClight Tavor Forend
    $125.00

    Please note, the ARClight Tavor Forend fits the Tavor SAR and is not compatible with the X95.

    The ARClight Tavor Forend is a direct replacement for the standard Tavor SAR polymer forend, and features ARC LOK slots that allow for attachment of Manticore Arms ARC LOK rail segments (sold separately) or the attachment of Magpul MOE compatible accessories. The ARClight Tavor Forend weighs 2 ounces less than the OEM polymer forend, and gives more mounting options and greater strength all with less weight.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 4.0 ounces

    Length: ?? inches

    Designed and Manufactured 100% in the USA

    Learn More
  3. ARClight Tavor Light Ring
    $35.95

    The Light Ring allows for mounting of a 1" light in the lower front of the ARClight Tavor Forend and ARClight Tavor XTL forend. In addition, the design of the Light Ring also acts as a cover plate for the front of the forend system. Pair it up with the IPSM Big Button on an ARClight XTL for the ultimate light mounting setup on a Tavor.

    The XTL model comes with the Light Ring and a top Filler Plate to completely seal the larger forend profile of the XTL forend when the Light Ring is installed in the front position.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: ?? ounces

    Length: N/A

    Designed and Manufactured 100% in the USA

    Learn More
  4. ARClight XTL Tavor Forend
    $180.95

    Please note, the ARClight XTL Tavor Forend fits the Tavor SAR and is not compatible with the X95.

    ARClight XTL Tavor Forend is a direct replacement for the standard Tavor polymer forend. Even better, the ARClight XTL is 3 inches longer than the existing forend, thus allowing additional mounting space for accessories and a grip further out on the gun, including on top of the front of the forend. It is made of completely monolithic construction, with no welds or fasteners that can fail!

    The ARClight XTL not only allows for additional mounting space, but also will allow for mounting of a standard 1" flashlight on both 16.5" and 18" barreled Tavors. and will also sleeve over any suppressor 1.75" in diameter or smaller.The forend also features two integrally machined QD sling swivel pockets on each side, and slots at the rear underside for wire routing for those who wish to place their pressure or tape switches on the outside or mount it on a vertical foregrip under the forearm.

    Naked is just the forend, nothing else.

    Fully Loaded is the forend, Light Ring, and (1) 5 slot and (1) 11 slot rail segment.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 8.1 ounces forend, 1.9 ounces light ring

    Length: 8.5 inches overall, projects 3 forward from face of upper receiver 

    100% designed and manufactured in the USA

    Learn More
  5. LUMA safety for Tavor
    $29.95

    (LUMA safeties work on both the Tavor and the X95 Tavor)

    The LUMA safety (Lever, Upgraded Metal Ambidextrous) is a direct drop in metal safety upgrade that will work on both the left and right side of the Tavor SAR and Tavor X95.  

    The LUMA safety can be purchased individually or as a pair. We recommend going with a MEDIUM safety on the firing thumb side and a SLIM safety on the offhand side, but you can order any combination you want.

    The LUMA safety is available in two variations:

    LUMA MEDIUM - the same pad size as the original polymer safety, but with sharp edges rounded and smoothed. Perfect for a full, positive activation pad.

    LUMA SLIM - a low profile version that keeps out of the way and won't irritate or rub your hand while in the "FIRE" position as the original polymer safety has been known to do, but that still allows for easy manipulation of the safety. Perfect for the offhand safety.

    PLEASE NOTE: The LUMA safety levers may be a little snug on installation, especially on the left side of the rifle. This is intentional to prevent slop and looseness of the safety when it is installed. The best way to install is to use a drop of oil in the keyway on the back of the LUMA safety, and start it on the lug by "angling in" and wiggling a bit- once started it becomes easier to slide on.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 0.1 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  6. Tavor Gasketed Port Cover
    $47.95

    (The Gasketed Port Cover will work on both the Tavor and X95 Tavor)

    The Tavor Gasketed Port Cover uses the unique solution of a compressible gasket to stop gas leakage through the ejection port cover and is ideal for use when running a suppressor. An inner and outer panel are pulled together by two screws and the gasket is sandwiched and compressed between the two panels which causes it to expand and fill in every gap and thus guarantee a gas tight seal regardless of irregularity in the surfaces to be sealed.  The Gasketed Port cover is will work on both the left and right side ejection ports of the Tavor SAR and X95 and has an integral QD pocket for a sling mounting point.  All hardware, tools, and instructions are included for installation.

    Material: 6061 aluminum and rubber like polymer

    Finish:  Type III milspec hardcoat black anodizing, black finish on rubber like polymer

    Weight: 1.7 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  7. Tavor Overwatch Full Length Top Rail
    $126.95

    The top rail on the Tavor SAR is notoriously low and designed for taller Israeli made optics. The Overwatch top rail raises the rail height up approximately 1/2" which makes the height of the Tavor optics rail over the stock the exact same as that of an AR-15, and allows for comfortably mounting and using all of the standard optics and iron sights available in the AR-15 focused U.S. market. The Overwatch Full Length rail features 40 picatinny slots and can be used as a carry handle by gripping the front portion above the upper handguard.

    Material: 6061 aluminum 

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 9.2 ounces

    Length: 14.5 inches

    Designed and Manufactured 100% in the USA

    Learn More
  8. Tavor Switchback Charging Handle
    $83.95

    Please note: The Tavor Switchback Charging Handle does not fit the X95.

    The Tavor Switchback is a folding charging handle that will work on either side of the Tavor. It offers the lowest possible profile when folded but a good two finger grip when deployed. The handle is folded out by hand, pulled back, and then released. The force of the handle going forward will cause it to flip forward, i.e. "switch back" to the stowage position and lock there via a spring loaded detent and small tab on the handle. The Tavor Switchbackconsists of an inner lug and rod assembly and an outer handle assemble which are attached by two screws and includes the componets, hardware, allen wrench, and instruction sheet necessary for installation. The Tavor Switchback not only can be mounted on either side of the Tavor but with a small modification to the inner plastic gas cover it is possible to run two handles on the rifle at the same time.

    Material: 6061 aluminum and steel rod

    Finish:  Type III milspec hardcoat black anodizing on aluminum and black oxide on steel

    Weight: 3.4 ounces

    Length: N/A

    Designed and Manufactured 100% in the USA

    Learn More
  9. ARClight Tavor Cover Plate
    $27.95

    Out of stock

    The Cover Plate allows you to close off the front end of the ARClight and ARClight XTL forend for when you do not want to mount a light internally. The Cover Plate is made from black anodized 6061 aluminum and is made in the USA. It includes all necessary hardware for mounting. Learn More
  10. Tavor Curved Buttpad
    $72.95

    Out of stock

    PLEASE NOTE THIS BUTTPAD WILL ONLY FIT THE "ORIGINAL" TAVOR (SAR MODEL) AND WILL NOT FIT THE X95

    Due to the large number of people who accidentally order this pad for their X95, if you order this for your X95 and want to return, you will have to return this buttpad for a refund on the price of it and re-order the correct one for the X95.   We will no longer do a "swap"  as we keep losing money on shipping from people do not reading the note above.

    The Tavor Curved Buttpad solves the length of pull and shouldering issues many people have with the existing Tavor rifle and buttpad.

    Manufactured from 6061 T6 aluminum and a specially chosen chemically resistant polymer with just a bit of "give" to it, the Tavor Curved Buttapd reduces the length of pull by almost an inch, and allows you to easily roll and lock the gun right into the shoulder pocket. Ribbing on the back and the texture of the polymer guarantee the gun will not slip around in the shoulder pocket once mounted. The special curved shape reduces the length of pull while keeping the overall length of the weapon the same as with the existing buttpad, which means that the gun stays just over 26" and there are no NFA issues.

    Material: 6061 aluminum and rubber like polymer

    Finish:  Black Cerakote on aluminum, black finish on rubber like polymer

    Weight: 5.3 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More

Grid List

Set Descending Direction

1-10 of 11

Page:
  1. 1
  2. 2