FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Shop All

Shop All

Grid List

Set Descending Direction

1-10 of 14

Page:
  1. 1
  2. 2
  1. Scorpion EVO  Slider Stock
    $257.95

    Inspired by the looks and function of the MP5A3 telescoping stock, the Scorpion EVO Slider Stock when fully collapsed only adds 3/4" of length and no additional width to the gun. The stock will lock at the closed position and also has four locking positions when extended. Maximum length of pull is 12.5"  and the gun can be fired with the stock open or even fully collapsed with no interference of the ejection port. The stock features a QD point on the mounting block left side and also a QD point on the top of the buttplate along with a sling loop on the underside of the buttplate. The buttplate is grooved for a good grip on the shoulder, and has the ability to mount an optional rubber buttpad if the user prefers.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 12.0 ounces

    Length: 9.125"

    100% designed and manufactured in the USA

    Learn More
  2. Scorpion EVO Bench Block
    $67.95

    The Bench Block is made of a heavy duty blue polymer that will not mar the surface of the receiver, and is shaped to fully support and distribute loads on the Scorpion EVO receiver while working on the gun. Four included bolts with nuts and washers are used to "clamshell" the receiver with the two blocks, and then the blocks, instead of the receiver, can be clamped into a vise to do work on the gun. An instruction sheet for proper use of the block is included.

    Please note that the OEM barrel nut is typically installed with thread locker, and that heat should be applied with a heat gun or carefully with a propane torch to break down the thread locker prior to trying to remove the barrel nut, even when using the Bench Block. We have seen some nuts come off with almost no force, and some require very high amounts of force to break them loose.

    If in doubt, take the gun to a Gunsmith to have the work done. Due to the inconsistent amount of thread locker used by CZ on the barrel nut Manticore Arms cannot be held liable for damage to the gun or components of the gun even when using the Bench Block.

    Material: Polymer

    Finish:  Black oxide

    Weight: 1 lb 4.0 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  3. Scorpion EVO E3 Safety Lever
    $24.95

    The Scorpion EVO E3 Safety (Enhanced Ergonomic EVO Safety) for is a direct drop in metal safety upgrade available for both the left and right side of the gun. Careful design of the shape, size, and location of the E3 prevents it from touching or rubbing on the index finger, and even if it does, it will not poke and gouge like the OEM safety lever. In addition the safety has been specifically designed to work with the OEM folding stock and Manticore's slider stock for the Scorpion EVO.

    Material:  6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight:  0.2 ounces

    Length:  N/A

    100% designed and manufactured in the USA

    Learn More
  4. Scorpion EVO Fixed Extended Charging Handle
    $58.95

    The Fixed Extended Charging Handle projects out 1/2" more than the OEM CZ charging handle thus giving more to grab onto for charging the gun.Manufactured all in house by Manticore Arms the aluminum handle is pinned to a steel rod assembly. All surfaces are contoured to remove sharp edges and the handle is large enough to allow for an "HK slap" to charge the weapon.

    A common solution with this upgrade is to use the Fixed Extended Charging Handle on the typical charging side and move the OEM charging handle to the offhand side, giving the option to charge the gun from either side when required.

    PLEASE NOTE: When removing the OEM or a Manticore charging handle from the scorpion, you will need to depress the detent spring through the lock pin hole to to prevent the spring from being bent, mangled, or damaged. Manticore Arms does not warranty springs damaged from improper removal of the handle. If in doubt on how to remove a handle properly, please email us at info@manticorearms.com

    Material: 6061 aluminum and steel rod

    Finish:  Type III milspec hardcoat black anodizing on aluminum and black oxide on steel

    Weight: 1.1 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  5. Scorpion EVO Muzzle Extension  18mm
    $59.95

    The Scorpion EVO Muzzle Extension 18mm gives you the look of a suppressor without the paperwork! Learn More
  6. Scorpion EVO Slider Stock Buttpad
    $20.00

    The Scorpion EVO Slider Stock Buttpad screws in via two supplied screws to the back of the Manticore Arms Scorpion EVO Slider Stock. This 1/2" thick internally reinforced buttpad will increase the length of pull and add a comfortable no-slip grip to the Slider Stock.

    Material:  Rubber like polymer with internal reinforcement

    Finish:  Black

    Weight: ?? ounces

    Length:  Adds 0.5" of length to Slider Stock

    100% designed and manufactured in the USA

    Learn More
  7. Scorpion EVO Switchback Charging Handle
    $82.95

    Based off the design of our incredibly popular and successful AUG Switchback and Tavor Switchback Charging Handles, the Scorpion EVO Switchback Charging Handle works in just the same way - fold out and pull back to charge the weapon and let go; the handle automatically returns to the folded position. It can even be locked into the holdback notch and given an "HK slap" and it will automatically go forward and fold.

    The best part is with the charging handle setup on the Scorpion EVO you can mount the Switchback Charging Handle on your primary charging side and mount your OEM handle on the off side, giving you dual charging ability on the gun.

    PLEASE NOTE: When removing the OEM or a Manticore charging handle from the scorpion, you will need to depress the detent spring through the lock pin hole to to prevent the spring from being bent, mangled, or damaged. Manticore Arms does not warranty springs damaged from improper removal of the handle. If in doubt on how to remove a handle properly, please email us at info@manticorearms.com

    PLEASE NOTE:   You are purchasing a single handle.  Photos show that two handles can be installed simultaneously and will work, but you have to order two handles to receive two handles.

    Material:  6061 aluminum and steel

    Finish:  Type III milspec hardcoat black anodizing on aluminum and black oxide on steel

    Weight:  1.2 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  8. Shadow Flash Hider 18mm Scorpion EVO
    $49.95

    Developed specifically for the Scorpion EVO this model of Shadow has 18mm threads, and three shorter straight prongs make the device more compact while still giving plenty of flash suppression for the 9mm cartridge.  Six detent notches allow the muzzle device to thread down as much as possible, and the device is marked "MA USA"  to denote USA manufacture for 922r compliance.

    Material: 8620 steel with Rockwell 50C heat treat

    Finish:  Black oxide

    Weight: 2.0 ounces

    Length:1.75 inches

    Designed and Manufactured 100% in the USA

    Learn More
  9. Scorpion EVO  PGS Hybrid Magazine 32 round
    $29.95

    Out of stock

    PLEASE NOTE: For Purchasing and warranty work please go to www.preppergunshop.com - Manticore Arms designed the magazines for Prepper, and all sales and warranty work are handled by Prepper Gun Shop. Manticore Arms does not sell or handle warranty service for this product.

    Developed for Prepper Gun Shop by Manticore Arms, the PGS Hybrid magazine for Scorpion EVO features heat treated feed lips and a polymer body. The magazine is 100% made in the USA and counts as three parts for 922r compliance. Available in Clear and Smoke Tint the magazine has a 32 round capacity and has round count markings molded into the body. MSRP is $29.95 and they are available for purchase at Prepper Gun Shop and their distributors

    https://www.preppergunshop.com/pgs-hybrid-scorpion-evo-mag-32-round-smoke-tint

    https://www.preppergunshop.com/pgs-hybrid-scorpion-evo-mag-32-round-clear

    Learn More
  10. Scorpion EVO  Slider Stock Buttplate Assembly
    $149.95

    Out of stock

    The Scorpion EVO Slider Stock Buttplate Assembly allows you to swap out the SB Tactical Arm Brace for an actual stock (all NFA laws apply) without needing to buy a whole new Slider Stock, you simply re-use the mounting block. When fully collapsed only adds 3/4" of length and no additional width to the gun. The stock will lock at the closed position and also has four locking positions when extended. Maximum length of pull is 12.5"  and the gun can be fired with the stock open or even fully collapsed with no interference of the ejection port. The buttplate a QD point on the top along with a sling loop on the underside. The buttplate is grooved for a good grip on the shoulder, and has the ability to mount an optional rubber buttpad if the user prefers.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 6.0 ounces

    Length: 9.125"

    100% designed and manufactured in the USA

    Learn More

Grid List

Set Descending Direction

1-10 of 14

Page:
  1. 1
  2. 2