FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

AK-47 and AK-74 rifle products

AK-47 and AK-74 rifle products

Grid List

Set Ascending Direction

11-14 of 14

Page:
  1. 1
  2. 2
  1. Eclipse Flash Hider 14x1L
    $64.95

    Designed specifically for the 308 and 7.62 mm caliber cartridge the 14 x 1 L Eclipse Flash Hider uses a slightly twisted triple prong design to reduce flash to near zero in even total darkness conditions.  The device is threaded 14 x 1 L metric  and will clear any projectile up to 311 caliber and 7.62 mm. Do not use with larger calibers.  The Eclipse Flash Hider is marked "MA" and "30" and a crush washer is included.  Use the crush washer instead of the detent pin for installation (detent pin may be left in place)

    Material: 8620 steel with Rockwell 50C heat treat

    Finish:  black oxide

    Weight: 3.6 ounces

    Length: 2.25 inches

    100% designed and manufactured in the USA

    Learn More
  2. PLM
    $112.95

    The Chinese Stock bolts to any standard 10-32 bolt pattern stock adapter or hinge, such as those offered by Stormwerkz and ACE Rifle Stocks, It is easily adapted to any AK and can even be mounted to a Yugo PAP pistol by drilling and tapping two 10-32 holes in the rear trunnion (make sure the pistol is registered as an SBR before doing this.)  The rear of the stock has a machined rib pattern to give a good grip on the shoulder, and with the use of a hinge it can be configured to fold left or right. The Chinese Stock comes with the stock, two 10-32 bolts and washers. The Chinese Stock is 8.5 inches long, hinge adds about 0.625 inches to the length when installed. Overall length of pull from buttplate to face of trigger with Chiense Stock and Stormwerkz Hinge installed is 12.25 inches which is exactly the same LOP as a real Russian or Bulgarian Sidefolder AK.

    The stock comes with a choice of Bakelite Orange, Russian Plum, or Black side panels with all the hardware necessary to install them and the panels can be left of to get a skeletonized look.

    Material: 6061 aluminum

    Finish: type III milspec hardcoat black anodizing

    Weight: 10.0 ounces with panels

    Length: 8.5 inches (stock only not including hinge or mounting blocks)

    100% designed and manufactured in the USA

    Learn More
  3. ALFA RAIL Keymod Forend Mini Draco
    $176.95

    Out of stock

    THE MA-12400 ALFA HANDGUARD WILL ONLY FIT THE MINI DRACO.

    The ALFA RAIL Keymod forend Min Draco gives the ability to use keymod accessories, mount an optic on the top picatinny, and even features an integral hand stop and QD sling swivel mounting point. The forend is installed like the standard Mini Draco handguard and is held in place by both the bolt on the underside and also features a flange that prevents the handguard from moving forward if the screw comes loose.

    An extremely precise and tight fight, in addition to careful design of the interface points with weapon ensures that the mounting is rock solid. The forend weighs only 4 oz, or approximately the same as the wood forend, yet offers much more in features. Manufactured from solid billets of 6061 T6 aluminum and anodized black the ALFA RAIL upper and lower include instructions and all hardware necessary for installation and are 100% made in the USA.

    Learn More
  4. ALFA RAIL Keymod Forend for stamped AK
    $118.95

    Out of stock

    PLEASE NOTE: THE ALFA LOWER FOREND OPTION FOR $119 IS ONLY THE LOWER PORTION, THE UPPER HANDGARD IS NOT INCLUDED WITH THIS OPTION! THE MA-11275 ALFA HANDGUARD WILL ONLY FIT STANDARD STAMPED 'EURO' AND 'CHINESE' AK'S.

    THIS MODEL WILL NOT FIT YUGO M-70/N-PAP/O-PAP, KRINKOVS, M92'S, UNCONVENRTED VEPR'S OR UNCONVERTED SAIGAS.

    The ALFA RAIL Keymod forend for the standard pattern AK gives the look and feel of a more traditional AK forend while giving the ability to mount Keymod accessories and other optional components, all while mounting exactly like the original handguard.

    The forend is simply installed like any standard AK handguard and is held in place by the front handguard retainer. An extremely precise and tight fight, in addition to careful design of the interface points with weapon ensures that the mounting is rock solid.

    Weighing 3.5 ounces it is actually almost an ounce lighter than the original polymer forend, yet several times stronger. An optional Superlow Optics Mount Upper which weighs only 2 ounces allows you to mount an Aimpoint Micro on its picatinny top rail and have co-witness with the iron sights.

    The ALFA RAIL lower forend will work with the standard polymer or wood upper handguard, or even with an Ultimak railed upper gas tube. Manufactured from solid billets of 6061 T6 aluminum and anodized black the ALFA RAIL upper and lower include instructions and all hardware necessary for installation and are 100% made in the USA.

    Material: 6061 aluminum

    Finish: Type III Milspec Hardcoat Black Anodizing

    Weight: 3.5 ounces lower rail, 2.0 ounces optional top cover

    Length: Standard AK forend

    100% designed and manufactured in the USA.

    Learn More

Grid List

Set Ascending Direction

11-14 of 14

Page:
  1. 1
  2. 2