FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Scorpion EVO  products

Scorpion EVO products

Grid List

Set Descending Direction

1-10 of 19

Page:
  1. 1
  2. 2
  1. Afterburner Linear Compensator 1/2x28 tpi
    $43.95

    The Afterburner Linear Compensator is one of the slimmest linear compensators on the market, yet is designed to give the same performance of larger "fatty" linear comps made by other companies. Measuring 1.00 inches in diameter and 2.25 inches in length with a 1.80 inch long inner chamber, the Afterburner features internal threading which serves dual purposes: distributing gas flow to reduce flash and provide a threaded surface where optional threaded muzzle ends, such as flash hider and compensator tips, can be added on for additional effect. The Afterburner will fit inside the Manticore Arms AR-15 Transformer Forend. The Afterburner Linear Compensator is marked "MA" and "USA" to denote 922r compliance and includes a crush washer and has wrench flats for ease of installation

    Material: 8620 steel with Rockwell 50C heat treat

    Finish:  Black oxide

    Weight: 3.4 ounces

    Length: 2.25 inches

    100% designed and manufactured in the USA

    Learn More
  2. Reverb Muzzle Brake 1/2 x 28 tpi
    $43.95

    The Reverb Muzzle Brake is a compact muzzle compensator that will work with any round under 9mm in diameter (i.e. 300 Blackout, 5.56mm, etc) on 1/2 x 28 tpi threaded barrels.

    Learn More
  3. Scorpion EVO  Slider Stock
    $257.95

    Inspired by the looks and function of the MP5A3 telescoping stock, the Scorpion EVO Slider Stock when fully collapsed only adds 3/4" of length and no additional width to the gun. The stock will friction lock at the closed position and can be "quick pulled" for instant deployment and will lock in the open position. Maximum length of pull is 12.5"  and the gun can be fired with the stock open or even fully collapsed with no interference of the ejection port. The stock features a QD point on the mounting block left side and also a QD point on the top of the buttplate along with a sling loop on the underside of the buttplate. The buttplate is grooved for a good grip on the shoulder, and has the ability to mount an optional rubber buttpad if the user prefers.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 12.0 ounces

    Length: 9.125"

    100% designed and manufactured in the USA

    Learn More
  4. Scorpion EVO 12" Carry Handle MLOK Forend
    $208.95

    PLEASE NOTE:  THIS FOREND IS ONLY RECOMMENDED FOR USE WITH A SCORPION EVO THAT HAS THE BULLPUP CONVERSION KIT INSTALLED.  THE SIGHT PLANE OF THE CARRY HANDLE WILL BE TOO HIGH FOR MOST USERS WHEN MOUNTED ON A STANDARD SCORPION EVO.

    The 12" Carry handle MLOK forend for Scorpion EVO offers no less than 23 slots of M-LOK across its 12" of length along with two integral QD points and is designed specifically to give a higher sight plane for use with Scorpion EVO's that are using the Bullpup Evo Conversion Kit. (It will fit all models of Scorpion EVO in standard configuration including the carbine, pistol, S2 Micro, but the sight plane will typically be too high for most users) .  Weighing in at 16.9 ounces including the mounting block it is actaully 0.5 ounces lighter than the 12" OEM polymer forend and has a built in carry handle to boot.  The forend will clear up to a 1.5" diameter suppressor, and uses an improved mounting block design which free floats the forend from the barrel. The forend comes with the forend, mounting block, and mounting hardware.  

    Material: 6061 aluminum

    Finish:  Type III Milspec black hardcoat andozing

    Weight: 16.9 ounces

    Length: 12 inches

    Designed and Manufactured 100% in the USA

    Learn More
  5. Scorpion EVO 12" MLOK Forend
    $158.95

    The 12" MLOK forend for Scorpion EVO offers no less than 27 slots of M-LOK across its 12" of length along with two integral QD points and will fit all models of Scorpion EVO including the carbine, pistol, S2 Micro, and EVO's using the Bullpup Conversion Kit .  Weighing in at 14.7 ounces including the mounting block it is actually 2.7 ounces lighter than the 12" OEM polymer forend.  The forend will clear up to a 1.5" diameter suppressor, and uses an improved mounting block design which free floats the forend from the barrel.  The forend comes with the forend, mounting block, and mounting hardwarde.  

    Material: 6061 aluminum

    Finish:  Type III Milspec black hardcoat andozing

    Weight: 14.7 ounces

    Length: 12 inches

    Designed and Manufactured 100% in the USA

    Learn More
  6. Scorpion EVO 15" Carry Handle MLOK Forend
    $229.95

    PLEASE NOTE:  THIS FOREND IS ONLY RECOMMENDED FOR USE WITH A SCORPION EVO THAT HAS THE BULLPUP CONVERSION KIT INSTALLED.  THE SIGHT PLANE OF THE CARRY HANDLE WILL BE TOO HIGH FOR MOST USERS WHEN MOUNTED ON A STANDARD SCORPION EVO.

    The 15" Carry handle MLOK forend for Scorpion EVO offers no less than 49 slots of M-LOK across its 15" of length along with two integral QD points and is designed specifically to give a higher sight plane for use with Scorpion EVO's that are using the Bullpup Evo Conversion Kit. (It will fit all models of Scorpion EVO in standard configuration including the carbine, pistol, S2 Micro, but the sight plane will typically be too high for most users) .  Weighing in at 18.6 ounces including the mounting block it is only 1.2  ounces heavier than the 12" OEM polymer forend, yet gives an additional 3" of length to completely wrap the barrel or a suppressor and has a built in carry handle.  The forend will clear up to a 1.5" diameter suppressor, and uses an improved mounting block design which free floats the forend from the barrel. The forend comes with the forend, mounting block, and mounting hardwarde.  

    Material: 6061 aluminum

    Finish:  Type III Milspec black hardcoat andozing

    Weight: 18.6 ounces

    Length: 15 inches

    Designed and Manufactured 100% in the USA

    Learn More
  7. Scorpion EVO 15" MLOK Forend
    $178.95

    The 15" MLOK forend for Scorpion EVO offers no less than 44 slots of M-LOK across its 15" of length along with two integral QD points and will fit all models of Scorpion EVO including the carbine, pistol, S2 Micro, and EVO's using the Bullpup Conversion Kit .  Weighing in at 19.4 ounces including the mounting block it is only 2.0 ounces heavier than the 12" OEM polymer forend, yet gives an additional 3" of length to completely wrap the barrel or a suppressor.  The forend will clear up to a 1.5" diameter suppressor, and uses an improved mounting block design which free floats the forend from the barrel.  The forend comes with the forend, mounting block, and mounting hardwarde.  

    Material: 6061 aluminum

    Finish:  Type III Milspec black hardcoat andozing

    Weight: 19.4 ounces

    Length: 15 inches

    Designed and Manufactured 100% in the USA

    Learn More
  8. Scorpion EVO Bench Block
    $67.95

    The Bench Block is made of a heavy duty blue polymer that will not mar the surface of the receiver, and is shaped to fully support and distribute loads on the Scorpion EVO receiver while working on the gun. Four included bolts with nuts and washers are used to "clamshell" the receiver with the two blocks, and then the blocks, instead of the receiver, can be clamped into a vise to do work on the gun. An instruction sheet for proper use of the block is included.

    Please note that the OEM barrel nut is typically installed with thread locker, and that heat should be applied with a heat gun or carefully with a propane torch to break down the thread locker prior to trying to remove the barrel nut, even when using the Bench Block. We have seen some nuts come off with almost no force, and some require very high amounts of force to break them loose.

    If in doubt, take the gun to a Gunsmith to have the work done. Due to the inconsistent amount of thread locker used by CZ on the barrel nut Manticore Arms cannot be held liable for damage to the gun or components of the gun even when using the Bench Block.

    Material: Polymer

    Finish:  Black oxide

    Weight: 1 lb 4.0 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  9. Scorpion EVO Bullpup Kit
    $395.00

    SPECIAL DEAL:  ORDER THE EVO BULLPUP KIT AND GET A FOREND UPGRADE AT 20% DISCOUNT!  CHOOSE YOUR OPTIONAL FOREND IN THE PULLDOWN MENU BELOW

    ALSO ADD A FOREND WRENCH AND/OR BENCH BLOCK IN THE SECOND PULLDOWN MENU- MAKES INSTALLTION OF THE FOREND EASIER!

    The Scorpion EVO Bullpup Kit designed by Manticore Arms and manufactured by CZ USA allows a standard Scorpion EVO carbine to be reduced in length to only 26.1" with a 16" barrel and still be a non NFA longarm!  Consisting of four major components - a new lower receiver, a buttplate, a cheekrest, and an optional optics riser, the EVO Bullpup Kit can convert a standard Scorpion EVO over the bullpup configuration in less than 15 minutes, and is fully reversible back to original configuration with no permanent modifications needed.

    In the bullpup configuration the safety is a crossbolt button located just above the new pistol grip location.  The upper receiver, trigger pack, trigger bow, pistol grip, and magazine release are re-used, and the kit will work with the original OEM carbine forend.  In addition the kit will work and can be upgraded with most any aftermarket trigger bow, pistol grip (some with minor modifications), magazine release, and trigger groups thus allowing the same level of upgrade and customization as any other Scorpion EVO.  Standard and aftermarket charging handles will also work on the bullpup conversion.

    The kit will also work with Manticore Arms EVO forends including both standard and carry handle models.  It will also work with the new Ratworx Venom integrally suppressed Scorpioon Forend! (Please note that due to required placement of M-LOK slots for mounting the bullpup lower receiver, ONLY the OEM carbine forend or Manticore Arms forends will work.  Other brands of forends may not allow proper mounting of the lower receiver)

    The buttpad is a kit specific version of the Manticore Arms Curved Buttpad found on most models of Tavor.  The kit is made of the same high grade polymer as the Scorpion EVO, and total weight of a carbine with kit installed is approximately 7 lbs 6 ounces.  The kit will function just fine with shorter barrels, but NFA regulations apply, and we recommend installing a suppressor of extended muzzle device to make sure the muzzle opening is at least flush with the end of the bullpup lower receiver.

    Please note that due to the new safety position that binary triggers will not be able to be mounted and function properly in the bullpup lower receiver pack and binary triggers are nto recommended in the kit.

     

    Material: high grade solid polymer, steel, aluminum rubber like polymer

    Finish:  Black 

    Weight: Kit 1 pound 14 ounces with optional riser, completed carbine weight 7 lbs 6 ounces  

    Length: 26.1" with 16" barrel

    100% designed and manufactured in the USA

    Learn More
  10. Scorpion EVO E3 Safety Lever
    $24.95

    The Scorpion EVO E3 Safety (Enhanced Ergonomic EVO Safety) for is a direct drop in metal safety upgrade available for both the left and right side of the gun. Careful design of the shape, size, and location of the E3 prevents it from touching or rubbing on the index finger, and even if it does, it will not poke and gouge like the OEM safety lever. In addition the safety has been specifically designed to work with the OEM folding stock and Manticore's slider stock for the Scorpion EVO.

    Material:  6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight:  0.2 ounces

    Length:  N/A

    100% designed and manufactured in the USA

    Learn More

Grid List

Set Descending Direction

1-10 of 19

Page:
  1. 1
  2. 2