FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Scorpion EVO  products

Scorpion EVO products

Grid List

Set Descending Direction

11-19 of 19

Page:
  1. 1
  2. 2
  1. Scorpion EVO Tri-Lug Adapter
    $49.95

    Developed specifically for the Scorpion EVO this model of the Eclipse has 18mm threads the Scorpion EVO Tri-Lug adapter mounts securely to the barrel with a 13/16" wrench (torque to approximately 25 ft lbs) and allows for mounting of all Tri-Lug accessories such as flash hiders and suppressors. The Scorpion EVO Tri-Lug Adapter is marked MA USA to denote a U.S. made part that counts towards 922r compliance.

    Material: 8620 steel with Rockwell 50C heat treat

    Finish:  Black oxide

    Weight: 2.0 ounces

    Length: 2.4 inches

    100% designed and manufactured in the USA

    Learn More
  2. Shadow Flash Hider 1/2 x 28 tpi
    $43.95

    The Shadow Flash Hider is a more compact and economical version of the Eclipse flash hider that features three short, straight prongs for excellent flash hiding capability. The Shadow Flash Hider will clear any round up to 9mm in diameter (i.e. 300 Blackout, 5.56mm, .22LR, etc) and is threaded 1/2 x 28 tpi. It is marked "MA" and "9mm" to denote that it is a 922r compliant part made in the USA by Manticore Arms for any weapon up to 9mm caliber and comes with a crush washer.

    Material: 8620 steel with Rockwell 50C heat treat

    Finish:  Black oxide

    Weight: 2.4 ounces

    Length: 1.75 inches

    100% designed and manufactured in the USA

    Learn More
  3. Scorpion EVO  Slider Stock Buttplate Assembly
    $149.95

    Out of stock

    The Scorpion EVO Slider Stock Buttplate Assembly allows you to swap out the SB Tactical Arm Brace for an actual stock (all NFA laws apply) without needing to buy a whole new Slider Stock, you simply re-use the mounting block. When fully collapsed only adds 3/4" of length and no additional width to the gun. The stock friction lock in the closed position and can be "rapid deployed" instantly with a pull and will lock in the open position. Maximum length of pull is 12.5"  and the gun can be fired with the stock open or even fully collapsed with no interference of the ejection port. The buttplate a QD point on the top along with a sling loop on the underside. The buttplate is grooved for a good grip on the shoulder, and has the ability to mount an optional rubber buttpad if the user prefers.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 6.0 ounces

    Length: 9.125"

    100% designed and manufactured in the USA

    Learn More
  4. Scorpion EVO Bullpup Kit
    $395.00

    Out of stock

    SPECIAL DEAL:  ORDER THE EVO BULLPUP KIT AND GET A FOREND UPGRADE AT 20% DISCOUNT!  CHOOSE YOUR OPTIONAL FOREND IN THE PULLDOWN MENU BELOW

    ALSO ADD A FOREND WRENCH AND/OR BENCH BLOCK IN THE SECOND PULLDOWN MENU- MAKES INSTALLTION OF THE FOREND EASIER!

    The Scorpion EVO Bullpup Kit designed by Manticore Arms and manufactured by CZ USA allows a standard Scorpion EVO carbine to be reduced in length to only 26.1" with a 16" barrel and still be a non NFA longarm!  Consisting of four major components - a new lower receiver, a buttplate, a cheekrest, and an optional optics riser, the EVO Bullpup Kit can convert a standard Scorpion EVO over the bullpup configuration in less than 15 minutes, and is fully reversible back to original configuration with no permanent modifications needed.

    In the bullpup configuration the safety is a crossbolt button located just above the new pistol grip location.  The upper receiver, trigger pack, trigger bow, pistol grip, and magazine release are re-used, and the kit will work with the original OEM carbine forend.  In addition the kit will work and can be upgraded with most any aftermarket trigger bow, pistol grip (some with minor modifications), magazine release, and trigger groups thus allowing the same level of upgrade and customization as any other Scorpion EVO.  Standard and aftermarket charging handles will also work on the bullpup conversion.

    The kit will also work with Manticore Arms EVO forends including both standard and carry handle models.  It will also work with the new Ratworx Venom integrally suppressed Scorpioon Forend! (Please note that due to required placement of M-LOK slots for mounting the bullpup lower receiver, ONLY the OEM carbine forend or Manticore Arms forends will work.  Other brands of forends may not allow proper mounting of the lower receiver)

    The buttpad is a kit specific version of the Manticore Arms Curved Buttpad found on most models of Tavor.  The kit is made of the same high grade polymer as the Scorpion EVO, and total weight of a carbine with kit installed is approximately 7 lbs 6 ounces.  The kit will function just fine with shorter barrels, but NFA regulations apply, and we recommend installing a suppressor of extended muzzle device to make sure the muzzle opening is at least flush with the end of the bullpup lower receiver.

    Please note that due to the new safety position that binary triggers will not be able to be mounted and function properly in the bullpup lower receiver pack and binary triggers are nto recommended in the kit.

     

    Material: high grade solid polymer, steel, aluminum rubber like polymer

    Finish:  Black 

    Weight: Kit 1 pound 14 ounces with optional riser, completed carbine weight 7 lbs 6 ounces  

    Length: 26.1" with 16" barrel

    100% designed and manufactured in the USA

    Learn More
  5. Scorpion EVO Carbine Barrel Nut Tool
    $35.00

    Out of stock

    Use this tool to remove the barrel nut on your CZ Scorpion Carbine. The carbine barrel nut (CZ-USA # 19343) is a standard 21mm hex, problem is that it is buried down inside of the long carbine handguard shroud. This tool acts like a VERY deep socket extension, the clearance inside of the tool allows it to be dropped down over the barrel, and engage the 21mm hex nut that secures the handguard in place.

    Please note that the torque spec for the barrel nut with a factory carbine handguard is 200 in*lbs, or about 16 ft*lbs. Over torquing the barrel nut can cause the factory handguard to crack or split.

    • Barrel Nut Tool for CZ Scorpion Carbine
    • Use with 1/2″ Ratchet or Breaker Bar
    • Made From Chromoly Steel and Zinc coated for corrosion resistance

    Designed and Manufactured completely in USA.

    Gunsmith Installation Recommended for All Parts.

    Learn More
  6. Scorpion EVO Muzzle Extension  18mm
    $59.95

    Out of stock

    The Scorpion EVO Muzzle Extension 18mm gives you the look of a suppressor without the paperwork! Learn More
  7. Scorpion EVO Pistol  Barrel Nut Tool
    $12.50

    Out of stock

    Use this tool to remove the barrel nut on your CZ Scorpion Pistol/SBR. The factory barrel nut (#2 on parts diagram) has two flats milled at 20mm. Our tool is designed to engage these flats and through the use of any 1/2″ ratchet or breaker bar remove this stubborn nut. Simply remove the flash hider, then place our tool onto the barrel nut and apply torque to rotate the nut approx 180 degrees, flip the tool, and repeat. Removing the barrel nut provides access to the handguard, barrel, trunnion, sling swivels, and other parts. Tool does NOT fit Scorpion Carbine, and 1/2″ ratchet is not included. 

    • Barrel Nut Tool for CZ Scorpion Pistol/SBR
    • Use with 1/2″ Ratchet or Breaker Bar
    • Made From Chromoly Steel

    Designed and Manufactured completely in USA.

    Gunsmith Installation Recommended for All Parts.

    Learn More
  8. Scorpion EVO Switchback Charging Handle
    $82.95

    Out of stock

    Based off the design of our incredibly popular and successful AUG Switchback and Tavor Switchback Charging Handles, the Scorpion EVO Switchback Charging Handle works in just the same way - fold out and pull back to charge the weapon and let go; the handle automatically returns to the folded position. It can even be locked into the holdback notch and given an "HK slap" and it will automatically go forward and fold.

    The best part is with the charging handle setup on the Scorpion EVO you can mount the Switchback Charging Handle on your primary charging side and mount your OEM handle on the off side, giving you dual charging ability on the gun.

    PLEASE NOTE: When removing the OEM or a Manticore charging handle from the scorpion, you will need to depress the detent spring through the lock pin hole to to prevent the spring from being bent, mangled, or damaged. Manticore Arms does not warranty springs damaged from improper removal of the handle. If in doubt on how to remove a handle properly, please email us at info@manticorearms.com

    PLEASE NOTE:   You are purchasing a single handle.  Photos show that two handles can be installed simultaneously and will work, but you have to order two handles to receive two handles.

    Material:  6061 aluminum and steel

    Finish:  Type III milspec hardcoat black anodizing on aluminum and black oxide on steel

    Weight:  1.2 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  9. Shadow Flash Hider 18mm Scorpion EVO
    $49.95

    Out of stock

    Developed specifically for the Scorpion EVO this model of Shadow has 18mm threads, and three shorter straight prongs make the device more compact while still giving plenty of flash suppression for the 9mm cartridge.  Six detent notches allow the muzzle device to thread down as much as possible, and the device is marked "MA USA"  to denote USA manufacture for 922r compliance.

    Material: 8620 steel with Rockwell 50C heat treat

    Finish:  Black oxide

    Weight: 2.0 ounces

    Length:1.75 inches

    Designed and Manufactured 100% in the USA

    Learn More

Grid List

Set Descending Direction

11-19 of 19

Page:
  1. 1
  2. 2