FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Tavor rifle products

Tavor rifle products

Grid List

Set Ascending Direction

1-10 of 16

Page:
  1. 1
  2. 2
  1. Tavor Switchback Charging Handle
    $83.95

    Please note: The Tavor Switchback Charging Handle does not fit the X95.

    The Tavor Switchback is a folding charging handle that will work on either side of the Tavor. It offers the lowest possible profile when folded but a good two finger grip when deployed. The handle is folded out by hand, pulled back, and then released. The force of the handle going forward will cause it to flip forward, i.e. "switch back" to the stowage position and lock there via a spring loaded detent and small tab on the handle. The Tavor Switchbackconsists of an inner lug and rod assembly and an outer handle assemble which are attached by two screws and includes the componets, hardware, allen wrench, and instruction sheet necessary for installation. The Tavor Switchback not only can be mounted on either side of the Tavor but with a small modification to the inner plastic gas cover it is possible to run two handles on the rifle at the same time.

    Material: 6061 aluminum and steel rod

    Finish:  Type III milspec hardcoat black anodizing on aluminum and black oxide on steel

    Weight: 3.4 ounces

    Length: N/A

    Designed and Manufactured 100% in the USA

    Learn More
  2. Tavor Gasketed Port Cover
    $47.95

    (The Gasketed Port Cover will work on both the Tavor and X95 Tavor)

    The Tavor Gasketed Port Cover uses the unique solution of a compressible gasket to stop gas leakage through the ejection port cover and is ideal for use when running a suppressor. An inner and outer panel are pulled together by two screws and the gasket is sandwiched and compressed between the two panels which causes it to expand and fill in every gap and thus guarantee a gas tight seal regardless of irregularity in the surfaces to be sealed.  The Gasketed Port cover is will work on both the left and right side ejection ports of the Tavor SAR and X95 and has an integral QD pocket for a sling mounting point.  All hardware, tools, and instructions are included for installation.

    Material: 6061 aluminum and rubber like polymer

    Finish:  Type III milspec hardcoat black anodizing, black finish on rubber like polymer

    Weight: 1.7 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  3. Tavor Curved Buttpad
    $72.95

    PLEASE NOTE THIS BUTTPAD WILL ONLY FIT THE "ORIGINAL" TAVOR (SAR MODEL) AND WILL NOT FIT THE X95

    Due to the large number of people who accidentally order this pad for their X95, if you order this for your X95 and want to return, you will have to return this buttpad for a refund on the price of it and re-order the correct one for the X95.   We will no longer do a "swap"  as we keep losing money on shipping from people do not reading the note above.

    The Tavor Curved Buttpad solves the length of pull and shouldering issues many people have with the existing Tavor rifle and buttpad.

    Manufactured from 6061 T6 aluminum and a specially chosen chemically resistant polymer with just a bit of "give" to it, the Tavor Curved Buttapd reduces the length of pull by almost an inch, and allows you to easily roll and lock the gun right into the shoulder pocket. Ribbing on the back and the texture of the polymer guarantee the gun will not slip around in the shoulder pocket once mounted. The special curved shape reduces the length of pull while keeping the overall length of the weapon the same as with the existing buttpad, which means that the gun stays just over 26" and there are no NFA issues.

    Material: 6061 aluminum and rubber like polymer

    Finish:  Black Cerakote on aluminum, black finish on rubber like polymer

    Weight: 5.3 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  4. Shadow Flash Hider 1/2 x 28 tpi
    $43.95

    The Shadow Flash Hider is a more compact and economical version of the Eclipse flash hider that features three short, straight prongs for excellent flash hiding capability. The Shadow Flash Hider will clear any round up to 9mm in diameter (i.e. 300 Blackout, 5.56mm, .22LR, etc) and is threaded 1/2 x 28 tpi. It is marked "MA" and "9mm" to denote that it is a 922r compliant part made in the USA by Manticore Arms for any weapon up to 9mm caliber and comes with a crush washer.

    Material: 8620 steel with Rockwell 50C heat treat

    Finish:  Black oxide

    Weight: 2.4 ounces

    Length: 1.75 inches

    100% designed and manufactured in the USA

    Learn More
  5. Reverb Muzzle Brake 1/2 x 28 tpi
    $43.95

    The Reverb Muzzle Brake is a compact muzzle compensator that will work with any round under 9mm in diameter (i.e. 300 Blackout, 5.56mm, etc) on 1/2 x 28 tpi threaded barrels.

    Learn More
  6. NightBrake for 1/2x28 tpi
    $64.95

    The Nightbrake provides both muzzle rise reduction and recoil reduction all in one.  A total of 18 ports distributed on the up half of the muzzle device help stabilize and reduce exiting gas pressure while the lack of ports on the underside prevent dust signature.  The Nightbrake is threaded 1/2 x 28 tpi and will clear any projectile up to 0.311  caliber or 7.62 mm, and is marked "MA" to denote it as a USA made 922r compliant part.  A crush washer is included with the muzzle device.

    Material: 8620 steel with Rockwell 50C heat treat

    Finish: Black oxide

    Weight:  2.0 ounces

    Length: 1.875 inches

    Learn More
  7. LUMA Slim safety for Tavor
    $29.95

    (LUMA safeties work on both the Tavor and the X95 Tavor)

    The LUMA safety (Lever, Upgraded Metal Ambidextrous) is a direct drop in metal safety upgrade that will work on both the left and right side of the Tavor SAR and Tavor X95.  

    The LUMA safety can be purchased individually or as a pair. We recommend going with a MEDIUM safety on the firing thumb side and a SLIM safety on the offhand side, but you can order any combination you want.

    The LUMA safety is available in two variations:

    LUMA MEDIUM - the same pad size as the original polymer safety, but with sharp edges rounded and smoothed. Perfect for a full, positive activation pad.

    LUMA SLIM - a low profile version that keeps out of the way and won't irritate or rub your hand while in the "FIRE" position as the original polymer safety has been known to do, but that still allows for easy manipulation of the safety. Perfect for the offhand safety.

    PLEASE NOTE: The LUMA safety levers may be a little snug on installation, especially on the left side of the rifle. This is intentional to prevent slop and looseness of the safety when it is installed. The best way to install is to use a drop of oil in the keyway on the back of the LUMA safety, and start it on the lug by "angling in" and wiggling a bit- once started it becomes easier to slide on.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 0.1 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  8. LUMA Medium safety for Tavor
    $29.95

    (LUMA safeties work on both the Tavor and the X95 Tavor)

    The LUMA safety (Lever, Upgraded Metal Ambidextrous) is a direct drop in metal safety upgrade that will work on both the left and right side of the Tavor SAR and Tavor X95.  

    The LUMA safety can be purchased individually or as a pair. We recommend going with a MEDIUM safety on the firing thumb side and a SLIM safety on the offhand side, but you can order any combination you want.

    The LUMA safety is available in two variations:

    LUMA MEDIUM - the same pad size as the original polymer safety, but with sharp edges rounded and smoothed. Perfect for a full, positive activation pad.

    LUMA SLIM - a low profile version that keeps out of the way and won't irritate or rub your hand while in the "FIRE" position as the original polymer safety has been known to do, but that still allows for easy manipulation of the safety. Perfect for the offhand safety.

    PLEASE NOTE: The LUMA safety levers may be a little snug on installation, especially on the left side of the rifle. This is intentional to prevent slop and looseness of the safety when it is installed. The best way to install is to use a drop of oil in the keyway on the back of the LUMA safety, and start it on the lug by "angling in" and wiggling a bit- once started it becomes easier to slide on.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 0.1 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  9. ARClight XTL IPSM "BIG BUTTON"
    $30.95

    The IPSM Big Button for ARClight XTL allows the pressure switch of the flashlight to be mounted internally in the forend while still being operated from the outside.  This is accomplished by the pressure swtich being mounting internally by an aluminum backer plate and a rubber button being mounted externally that can be pressed to activate the now internal pressure switch.  This keeps the pressure switch and cord inside the forend safe and free from snags and damage.

    The kit and pressure switch can be mounted on the left or right sides of the forend to offer more flexibility in position.  The IPSM kit includes the rubber big button, aluminum backing plate, adjustment screws, and instruction sheet and is 100% made in the USA.

    Material:  6061 aluminum and rubber

    FInish:  Type III Hardcoat Mislpec Anodizing

    Weight: 1.0 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  10. ARClight Tavor Light Ring
    $35.95

    The Light Ring allows for mounting of a 1" light in the lower front of the ARClight Tavor Forend and ARClight Tavor XTL forend. In addition, the design of the Light Ring also acts as a cover plate for the front of the forend system. Pair it up with the IPSM Big Button on an ARClight XTL for the ultimate light mounting setup on a Tavor.

    The XTL model comes with the Light Ring and a top Filler Plate to completely seal the larger forend profile of the XTL forend when the Light Ring is installed in the front position.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: ?? ounces

    Length: N/A

    Designed and Manufactured 100% in the USA

    Learn More

Grid List

Set Ascending Direction

1-10 of 16

Page:
  1. 1
  2. 2