FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Tavor rifle products

Tavor rifle products

Grid List

Set Ascending Direction

11-17 of 17

Page:
  1. 1
  2. 2
  1. ARClight Tavor Forend
    $125.00

    Please note, the ARClight Tavor Forend fits the Tavor SAR and is not compatible with the X95.

    The ARClight Tavor Forend is a direct replacement for the standard Tavor SAR polymer forend, and features ARC LOK slots that allow for attachment of Manticore Arms ARC LOK rail segments (sold separately) or the attachment of Magpul MOE compatible accessories. The ARClight Tavor Forend weighs 2 ounces less than the OEM polymer forend, and gives more mounting options and greater strength all with less weight.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 4.0 ounces

    Length: ?? inches

    Designed and Manufactured 100% in the USA

    Learn More
  2. ARClight Pathfinder Tavor Forend
    $199.95

    ***PLEASE NOTE THIS IS A SPECIAL RUN WITH LIMITED QUANTITIES***

    The Pathfinder is a direct replacement for the OEM polymer Tavor SAR forend, is 7 inches longer than the OEM forend, and is intended to act as heat protection against a suppressor that is mounted to the barrel. The monolithic design allows it to sleeve over any suppressor up to 1.75" in diameter, and most suppressors will have approximately one inch visible out the front of the forend. ARC LOK slots on the entire surface let you mount any combination of accessories and grip further out on the gun, including on top of the front of the forend. It is made of completely monolithic construction, with no welds or fasteners to fail.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 13.4 ounces

    Length: ?? inches

    Designed and Manufactured 100% in the USA

    Learn More
  3. ARClight ARC LOK aluminum rail segments
    $23.00

    Available in either 5 slots and 11 slot lengths, the ARClight ARC LOK rail segments are designed specifically to attach to all ARClight forearm and rail systems.

    Made from 6061 aluminum and anodized black, the rail segments are attached through our patent pending ARC LOK rotating tabs- there is no need to be able to access the back side of the mounting surface, just insert the rail segment, rotate the screws 2-3 turns counterclockwise, then rotate clockwise until tight and it is attached!

    Lugs on the back of the rail interface with the ARClight slots and transfer the forces directly to the ARClight forearm or rail system, instead of through the screws like most other attachable rail systems. ARClight rail segments are made in the USA and come with steel backer bar, mounting screws, and an allen wrench for easy installation.

    Material:  6061 Aluminum

    Finish: Type III Hardcoat Milspec Anodizing

    Wieght: ??

    Length: ??

    Learn More
  4. Afterburner Linear Compensator 1/2x28 tpi
    $43.95

    The Afterburner Linear Compensator is one of the slimmest linear compensators on the market, yet is designed to give the same performance of larger "fatty" linear comps made by other companies. Measuring 1.00 inches in diameter and 2.25 inches in length with a 1.80 inch long inner chamber, the Afterburner features internal threading which serves dual purposes: distributing gas flow to reduce flash and provide a threaded surface where optional threaded muzzle ends, such as flash hider and compensator tips, can be added on for additional effect. The Afterburner will fit inside the Manticore Arms AR-15 Transformer Forend. The Afterburner Linear Compensator is marked "MA" and "USA" to denote 922r compliance and includes a crush washer and has wrench flats for ease of installation

    Material: 8620 steel with Rockwell 50C heat treat

    Finish:  Black oxide

    Weight: 3.4 ounces

    Length: 2.25 inches

    100% designed and manufactured in the USA

    Learn More
  5. Tavor Overwatch Medium Length Top Rail
    $104.95

    Out of stock

    The top rail on the Tavor SAR is notoriously low and designed for taller Israeli made optics. The Overwatch top rail raises the rail height up approximately 1/2" which makes the height of the Tavor optics rail over the stock the exact same as that of an AR-15, and allows for comfortably mounting and using all of the standard optics and iron sights available in the AR-15 focused U.S. market. The Overwatch Medium Length Top Rail rail features 21 picatinny slots and is shorter for those preferring a more compact and lighter setup.

    Material: 6061 aluminum 

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 6.9 ounces

    Length: 9 inches

    100% designed and manufactured in the USA

    Learn More
  6. Tavor Curved Buttpad
    $72.95

    Out of stock

    PLEASE NOTE THIS BUTTPAD WILL ONLY FIT THE "ORIGINAL" TAVOR (SAR MODEL) AND WILL NOT FIT THE X95

    Due to the large number of people who accidentally order this pad for their X95, if you order this for your X95 and want to return, you will have to return this buttpad for a refund on the price of it and re-order the correct one for the X95.   We will no longer do a "swap"  as we keep losing money on shipping from people do not reading the note above.

    The Tavor Curved Buttpad solves the length of pull and shouldering issues many people have with the existing Tavor rifle and buttpad.

    Manufactured from 6061 T6 aluminum and a specially chosen chemically resistant polymer with just a bit of "give" to it, the Tavor Curved Buttapd reduces the length of pull by almost an inch, and allows you to easily roll and lock the gun right into the shoulder pocket. Ribbing on the back and the texture of the polymer guarantee the gun will not slip around in the shoulder pocket once mounted. The special curved shape reduces the length of pull while keeping the overall length of the weapon the same as with the existing buttpad, which means that the gun stays just over 26" and there are no NFA issues.

    Material: 6061 aluminum and rubber like polymer

    Finish:  Black Cerakote on aluminum, black finish on rubber like polymer

    Weight: 5.3 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  7. ARClight Tavor Cover Plate
    $27.95

    Out of stock

    The Cover Plate allows you to close off the front end of the ARClight and ARClight XTL forend for when you do not want to mount a light internally. The Cover Plate is made from black anodized 6061 aluminum and is made in the USA. It includes all necessary hardware for mounting. Learn More

Grid List

Set Ascending Direction

11-17 of 17

Page:
  1. 1
  2. 2