FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Tavor rifle products

Tavor rifle products

Grid List

Set Descending Direction

1-10 of 17

Page:
  1. 1
  2. 2
  1. Afterburner Linear Compensator 1/2x28 tpi
    $43.95

    The Afterburner Linear Compensator is one of the slimmest linear compensators on the market, yet is designed to give the same performance of larger "fatty" linear comps made by other companies. Measuring 1.00 inches in diameter and 2.25 inches in length with a 1.80 inch long inner chamber, the Afterburner features internal threading which serves dual purposes: distributing gas flow to reduce flash and provide a threaded surface where optional threaded muzzle ends, such as flash hider and compensator tips, can be added on for additional effect. The Afterburner will fit inside the Manticore Arms AR-15 Transformer Forend. The Afterburner Linear Compensator is marked "MA" and "USA" to denote 922r compliance and includes a crush washer and has wrench flats for ease of installation

    Material: 8620 steel with Rockwell 50C heat treat

    Finish:  Black oxide

    Weight: 3.4 ounces

    Length: 2.25 inches

    100% designed and manufactured in the USA

    Learn More
  2. ARClight Pathfinder Tavor Forend
    $199.95

    ***PLEASE NOTE THIS IS A SPECIAL RUN WITH LIMITED QUANTITIES***

    The Pathfinder is a direct replacement for the OEM polymer Tavor SAR forend, is 7 inches longer than the OEM forend, and is intended to act as heat protection against a suppressor that is mounted to the barrel. The monolithic design allows it to sleeve over any suppressor up to 1.75" in diameter, and most suppressors will have approximately one inch visible out the front of the forend. ARC LOK slots on the entire surface let you mount any combination of accessories and grip further out on the gun, including on top of the front of the forend. It is made of completely monolithic construction, with no welds or fasteners to fail.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 13.4 ounces

    Length: ?? inches

    Designed and Manufactured 100% in the USA

    Learn More
  3. ARClight Tavor Cover Plate
    $27.95

    The Cover Plate allows you to close off the front end of the ARClight and ARClight XTL forend for when you do not want to mount a light internally. The Cover Plate is made from black anodized 6061 aluminum and is made in the USA. It includes all necessary hardware for mounting. Learn More
  4. ARClight Tavor Forend
    $125.00

    Please note, the ARClight Tavor Forend fits the Tavor SAR and is not compatible with the X95.

    The ARClight Tavor Forend is a direct replacement for the standard Tavor SAR polymer forend, and features ARC LOK slots that allow for attachment of Manticore Arms ARC LOK rail segments (sold separately) or the attachment of Magpul MOE compatible accessories. The ARClight Tavor Forend weighs 2 ounces less than the OEM polymer forend, and gives more mounting options and greater strength all with less weight.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 4.0 ounces

    Length: ?? inches

    Designed and Manufactured 100% in the USA

    Learn More
  5. ARClight Tavor Light Ring
    $35.95

    The Light Ring allows for mounting of a 1" light in the lower front of the ARClight Tavor Forend and ARClight Tavor XTL forend. In addition, the design of the Light Ring also acts as a cover plate for the front of the forend system. Pair it up with the IPSM Big Button on an ARClight XTL for the ultimate light mounting setup on a Tavor.

    The XTL model comes with the Light Ring and a top Filler Plate to completely seal the larger forend profile of the XTL forend when the Light Ring is installed in the front position.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: ?? ounces

    Length: N/A

    Designed and Manufactured 100% in the USA

    Learn More
  6. ARClight XTL IPSM "BIG BUTTON"
    $30.95

    The IPSM Big Button for ARClight XTL allows the pressure switch of the flashlight to be mounted internally in the forend while still being operated from the outside.  This is accomplished by the pressure swtich being mounting internally by an aluminum backer plate and a rubber button being mounted externally that can be pressed to activate the now internal pressure switch.  This keeps the pressure switch and cord inside the forend safe and free from snags and damage.

    The kit and pressure switch can be mounted on the left or right sides of the forend to offer more flexibility in position.  The IPSM kit includes the rubber big button, aluminum backing plate, adjustment screws, and instruction sheet and is 100% made in the USA.

    Material:  6061 aluminum and rubber

    FInish:  Type III Hardcoat Mislpec Anodizing

    Weight: 1.0 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  7. ARClight XTL Tavor Forend
    $180.95

    Please note, the ARClight XTL Tavor Forend fits the Tavor SAR and is not compatible with the X95.

    ARClight XTL Tavor Forend is a direct replacement for the standard Tavor polymer forend. Even better, the ARClight XTL is 3 inches longer than the existing forend, thus allowing additional mounting space for accessories and a grip further out on the gun, including on top of the front of the forend. It is made of completely monolithic construction, with no welds or fasteners that can fail!

    The ARClight XTL not only allows for additional mounting space, but also will allow for mounting of a standard 1" flashlight on both 16.5" and 18" barreled Tavors. and will also sleeve over any suppressor 1.75" in diameter or smaller.The forend also features two integrally machined QD sling swivel pockets on each side, and slots at the rear underside for wire routing for those who wish to place their pressure or tape switches on the outside or mount it on a vertical foregrip under the forearm.

    Naked is just the forend, nothing else.

    Fully Loaded is the forend, Light Ring, and (1) 5 slot and (1) 11 slot rail segment.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 8.1 ounces forend, 1.9 ounces light ring

    Length: 8.5 inches overall, projects 3 forward from face of upper receiver 

    100% designed and manufactured in the USA

    Learn More
  8. LUMA safety for Tavor
    $29.95

    (LUMA safeties work on both the Tavor and the X95 Tavor)

    The LUMA safety (Lever, Upgraded Metal Ambidextrous) is a direct drop in metal safety upgrade that will work on both the left and right side of the Tavor SAR and Tavor X95.  

    The LUMA safety can be purchased individually or as a pair. We recommend going with a MEDIUM safety on the firing thumb side and a SLIM safety on the offhand side, but you can order any combination you want.

    The LUMA safety is available in two variations:

    LUMA MEDIUM - the same pad size as the original polymer safety, but with sharp edges rounded and smoothed. Perfect for a full, positive activation pad.

    LUMA SLIM - a low profile version that keeps out of the way and won't irritate or rub your hand while in the "FIRE" position as the original polymer safety has been known to do, but that still allows for easy manipulation of the safety. Perfect for the offhand safety.

    PLEASE NOTE: The LUMA safety levers may be a little snug on installation, especially on the left side of the rifle. This is intentional to prevent slop and looseness of the safety when it is installed. The best way to install is to use a drop of oil in the keyway on the back of the LUMA safety, and start it on the lug by "angling in" and wiggling a bit- once started it becomes easier to slide on.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 0.1 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  9. NightBrake for 1/2x28 tpi
    $64.95

    The Nightbrake provides both muzzle rise reduction and recoil reduction all in one.  A total of 18 ports distributed on the up half of the muzzle device help stabilize and reduce exiting gas pressure while the lack of ports on the underside prevent dust signature.  The Nightbrake is threaded 1/2 x 28 tpi and will clear any projectile up to 0.311  caliber or 7.62 mm, and is marked "MA" to denote it as a USA made 922r compliant part.  A crush washer is included with the muzzle device.

    Material: 8620 steel with Rockwell 50C heat treat

    Finish: Black oxide

    Weight:  2.0 ounces

    Length: 1.875 inches

    Learn More
  10. Reverb Muzzle Brake 1/2 x 28 tpi
    $43.95

    The Reverb Muzzle Brake is a compact muzzle compensator that will work with any round under 9mm in diameter (i.e. 300 Blackout, 5.56mm, etc) on 1/2 x 28 tpi threaded barrels.

    Learn More

Grid List

Set Descending Direction

1-10 of 17

Page:
  1. 1
  2. 2