FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Stocks and Arm Braces

Stocks and Arm Braces

Grid List

Set Descending Direction

1-10 of 12

Page:
  1. 1
  2. 2
  1. Bren 2 Picatinny Mounting Block
    $104.95

    The Bren 2 Picatinny Mounting Block allows for mounting of picatinny style stocks, arm braces, and accessories of all sorts on the butt of the Bren 2 and Bren 2 MS rifles and pistols.

    The block is pre-assembled and is easily installed by simply pulling the front pin on the lower, tilting out and removing, then removing the existing mounting block, and sliding the Bren 2 Picatinny Mounting Block upwards and into place where it will secure itself with a "click" (make sure the recoil spring assembly is all the way in the gun before pressing upwards on the block). Removal is just as simple, pull back a small spring loaded lever on the underside, slide the block down and it will come right off.  The spring loaded locking piece keeps it snugly on the the gun with no movement, and makes installation and removal extremely easy with no tools.

    Material:  6061 aluminum

    Finish:  Type III milspec black anodizing

    Weight: 5.8 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  2. Bren 2 Sidefolder Mounting Block
    $104.95

    The Bren 2 Picatinny Mounting Block allows for mounting of sidefolder stocks, arm braces, on the Bren 2 and Bren 2 MS rifles and pistols.  The block is designed to work with the standard SB Tactical sidefolding arm braces, and will also work with B&T sidefolder stocks if the hinge pin hole is drilled out to 3/16" (0.188").  Other stocks and arm braces may work if set up with a similar hinge pin and button dimensions.

    The block is pre-assembled and is easily installed by simply pulling the front pin on the lower, tilting out and removing, then removing the existing mounting block, and sliding the Bren 2 Picatinny Mounting Block upwards and into place where it will secure itself with a "click" (make sure the recoil spring assembly is all the way in the gun before pressing upwards on the block). Removal is just as simple, pull back a small spring loaded lever on the underside, slide the block down and it will come right off.  The spring loaded locking piece keeps it snugly on the the gun with no movement, and makes installation and removal extremely easy with no tools.

    To install a stock or arm brace, drill out the hinge pin hole to 3/16" (0.188").  SB Tactical arm braces usually will be a bit snug but should with the hole in them being approximately 0.180".  It is recommended to put a bit of white lithium grease on the included 2" long  partially threaded 10-32 socket head screw.  Lock the stock or arm brace into position as though deployed, and align the hinge pin hole, then turn the screw down through the hole until the head is completely set in its pocket.  If the stock is too snug to fold, back off the screw 1/4 to 1/2 turn, and if it is a little loose, give it another 1/4 to 1/2 turn.  The preferred friction lock in the folded position can be adjusted this way.

    NOTE:  Due to the length of the receiver length and trigger location on the Bren 2 the SB Tactical SBT arm brace will have a 14.0" length of pull when deployed.  As of this time (12/02/2020) ATF has not officially or  publicly published any guidelines on allowable length of pull for deployed arm braces.  Manticore Arms cannot provide legal advice on the assembly or use of products.  

    Material:  6061 aluminum

    Finish:  Type III milspec black anodizing

    Weight: 6.0 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  3. Chinese Stock
    $112.95

    Get the look of a Chinese sidefolder stock without the hassle of a complete rebuild on your gun!

    The MA-16500 Chinese Stock bolts to any standard 10-32 bolt pattern stock adapter or hinge, such as those offered by Stormwerkz and ACE Rifle Stocks.  It ismade of 6061 aluminum that is bead blasted and anodized black, and with polymer panels on both sides, The stock comes with a choice of Bakelite Orange, Russian Plum, or Black side panels with all the hardware necessary to install them, and the panels can be left off for a skeletonized look.

    The rear of the stock has a machined rib pattern to give a good grip on the shoulder, and with the use of a hinge it can be configured to fold left or right. The MA-16500 Chinese Stock  comes with the stock, two 10-32 bolts and washers, is 8.5" long.

    Material: 6061 Aluminum

    Finish: Milspec Black Type III Hard Anodizing

    Weight: 10.0 ounces with panels

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  4. Chinese Stock Spare Panel Set
  5. Scorpion EVO  Slider Stock
    $257.95

    Inspired by the looks and function of the MP5A3 telescoping stock, the Scorpion EVO Slider Stock when fully collapsed only adds 3/4" of length and no additional width to the gun. The stock will friction lock at the closed position and can be "quick pulled" for instant deployment and will lock in the open position. Maximum length of pull is 12.5"  and the gun can be fired with the stock open or even fully collapsed with no interference of the ejection port. The stock features a QD point on the mounting block left side and also a QD point on the top of the buttplate along with a sling loop on the underside of the buttplate. The buttplate is grooved for a good grip on the shoulder, and has the ability to mount an optional rubber buttpad if the user prefers.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 12.0 ounces

    Length: 9.125"

    100% designed and manufactured in the USA

    Learn More
  6. Scorpion EVO  Slider Stock Buttplate Assembly
    $149.95

    The Scorpion EVO Slider Stock Buttplate Assembly allows you to swap out the SB Tactical Arm Brace for an actual stock (all NFA laws apply) without needing to buy a whole new Slider Stock, you simply re-use the mounting block. When fully collapsed only adds 3/4" of length and no additional width to the gun. The stock friction lock in the closed position and can be "rapid deployed" instantly with a pull and will lock in the open position. Maximum length of pull is 12.5"  and the gun can be fired with the stock open or even fully collapsed with no interference of the ejection port. The buttplate a QD point on the top along with a sling loop on the underside. The buttplate is grooved for a good grip on the shoulder, and has the ability to mount an optional rubber buttpad if the user prefers.

    Material: 6061 aluminum

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 6.0 ounces

    Length: 9.125"

    100% designed and manufactured in the USA

    Learn More
  7. Tavor 7 Curved Buttpad
    $72.95

    PLEASE NOTE THIS BUTTPAD WILL ONLY FIT THE  TAVOR 7.  IT WILL NOT FIT THE TAVOR SAR OR TAVOR X95

    Similar to our Tavor Curved Buttpad, the Tavor 7 Curved Buttpad features an aluminum skeleton structure with an overmolded rubber pad.  The rubber pad is curved to conform to the shoulder and gives both better ergonomics and a better grip so the rifle does not slide around.

    The Tavor 7 Curved Buttpad is made by Manticore Arms in the USA.

     Please be sure to order the correct buttpad for your rifle, and if not sure please contact customer service at info@manticorearms.com

     

    Material: 6061 aluminum and rubber like polymer

    Finish:  Black Cerakote on aluminum, black finish on rubber like polymer

    Weight: 6.5 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  8. Tavor Curved Buttpad
    $72.95

    PLEASE NOTE THIS BUTTPAD WILL ONLY FIT THE "ORIGINAL" TAVOR (SAR MODEL) AND WILL NOT FIT THE X95

    Due to the large number of people who accidentally order this pad for their X95, if you order this for your X95 and want to return, you will have to return this buttpad for a refund on the price of it and re-order the correct one for the X95.   We will no longer do a "swap"  as we keep losing money on shipping from people do not reading the note above.

    The Tavor Curved Buttpad solves the length of pull and shouldering issues many people have with the existing Tavor rifle and buttpad.

    Manufactured from 6061 T6 aluminum and a specially chosen chemically resistant polymer with just a bit of "give" to it, the Tavor Curved Buttapd reduces the length of pull by almost an inch, and allows you to easily roll and lock the gun right into the shoulder pocket. Ribbing on the back and the texture of the polymer guarantee the gun will not slip around in the shoulder pocket once mounted. The special curved shape reduces the length of pull while keeping the overall length of the weapon the same as with the existing buttpad, which means that the gun stays just over 26" and there are no NFA issues.

    Material: 6061 aluminum and rubber like polymer

    Finish:  Black Cerakote on aluminum, black finish on rubber like polymer

    Weight: 5.3 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  9. Tavor TS12 Shotgun Curved Buttpad
    $72.95

    PLEASE NOTE THIS BUTTPAD WILL ONLY FIT THE  TAVOR TS12 SHOTGUN.  IT WILL NOT FIT THE TAVOR SAR, TAVOR X95, OR TAVOR 7

    Similar to our Tavor Curved Buttpad, the Tavor TS12 Shotgun Curved Buttpad features an aluminum skeleton structure with an overmolded rubber pad.  The rubber pad is curved to conform to the shoulder and gives both better ergonomics and a better grip so the rifle does not slide around, and has an additoinal 1" of "drop" at the toe over the OEM buttpad to give a much larger surface area and the ability to ride the shotgun higher on the shoulder for a more inline stance.

    The Tavor TS12 Shotgun Curved Buttpad is made by Manticore Arms in the USA.

     Please be sure to order the correct buttpad for your rifle, and if not sure please contact customer service at info@manticorearms.com

     

    Material: 6061 aluminum and rubber like polymer

    Finish:  Black Cerakote on aluminum, black finish on rubber like polymer

    Weight: 11.4 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  10. Triangle Stock
    $112.95

    Please note, no hinge or mounting block is included, these can be purchase at stormwerkz.com or a variety of other suppliers.

    The Triangle Stock bolts to any standard 10-32 bolt pattern stock adapter or hinge, such as those offered by Stormwerkz and ACE Riflestocks.  It is easily adapted to any AK, and can even be mounted to a Yugo PAP pistol by simply drilling and tapping two 10-32 holes in the rear trunnion (make sure the pistol is registered as an SBR before doing this.)

    Made of 6061 aluminum that is bead blasted and anodized black, the stock weighs only 10.0 ounces as the arms and rear of the stock are now scallop cut internally to reduce weight, and with a hinge installed will have the exact length of a true Russian or Bulgarian sidefolder stock. The rear of the stock has a machined rib pattern to give a good grip on the shoulder, and with the use of a hinge it can be configured to fold left or right. The Triangle Stock comes with the stock, two 10-32 bolts and washers. Overall LOP (Length Of Pull from buttplate to face of trigger) with Triangle Stock and Stormwerkz or Ace Riflestock Hinge installed is 12.25", exactly the same LOP as a real Russian or Bulgarian Sidefolder AK.

    Material: 6061 aluminum

    Finish: Type III milspec hardcoat black anodizing

    Weight: 11.0 ounces

    Length: 8.5 inches (stock only not including hinge or mounting blocks)

    100% designed and manufactured in the USA

    Learn More

Grid List

Set Descending Direction

1-10 of 12

Page:
  1. 1
  2. 2