FLAT RATE SHIPPING ON ALL ORDERS!

QUESTIONS? CALL 866-331-9472

Shop All

Shop All

Grid List

Set Ascending Direction

41-50 of 77

  1. Eclipse Flash Hider 5/8x24 tpi
    $64.95

    Designed specifically for the .308 and 7.62mm caliber cartridge the 5/8 x 24 tpi Eclipse Flash Hider uses a slightly twisted triple prong design to reduce flash to near zero in even total darkness conditions.  The device is threaded 5/8 x 24 tpi and will clear any projectile up to .308  caliber and 7.62 mm. Do not use with larger calibers.  The Eclipse Flash Hider is marked "MA" and "30" and a crush washer is included.

    Material: 8620 steel with Rockwell 50C heat treat

    Finish:  Black oxide

    Weight: 3.6 ounces

    Length: 2.25 inches

    100% designed and manufactured in the USA

    Learn More
  2. Eclipse Flash Hider 24mm
    $64.95

    Designed specifically for the 308  and 7.62 mm caliber cartridge the 24 mm Eclipse Flash Hider uses a slightly twisted triple prong design to reduce flash to near zero in even total darkness conditions.  The device is threaded 24mm  and will clear any projectile up to .311 caliber and 7.62 mm. Do not use with larger calibers.  The 24 mm Eclipse Flash Hider is marked "MA" and "30" and has multiple detent notches to allow it to thread down as far as possible.

    Material: 8620 steel with Rockwell 50C heat treat

    Finish:  Black oxide

    Weight: 3.6 ounces

    Length: 2.25 inches

    100% designed and manufactured in the USA

    Learn More
  3. Eclipse Flash Hider 14x1L
    $64.95

    Designed specifically for the 308 and 7.62 mm caliber cartridge the 14 x 1 L Eclipse Flash Hider uses a slightly twisted triple prong design to reduce flash to near zero in even total darkness conditions.  The device is threaded 14 x 1 L metric  and will clear any projectile up to 311 caliber and 7.62 mm. Do not use with larger calibers.  The Eclipse Flash Hider is marked "MA" and "30" and a crush washer is included.  Use the crush washer instead of the detent pin for installation (detent pin may be left in place)

    Material: 8620 steel with Rockwell 50C heat treat

    Finish:  black oxide

    Weight: 3.6 ounces

    Length: 2.25 inches

    100% designed and manufactured in the USA

    Learn More
  4. Eclipse Flash Hider 1/2x28 tpi
    $64.95

    Designed specifically for the .223 and 5.56 mm caliber cartridge the Eclipse Flash Hider uses a slightly twisted triple prong design to reduce flash to near zero in even total darkness conditions.  The device is threaded 1/2 x 28 tpi and will clear any projectile up to .223 caliber and 5.56 mm. Do not use with larger calibers.  The Eclipse Flash Hider is marked "MA" and "223" and a crush washer is included.

    Material: 8620 steel with Rockwell 50C heat treat

    Finish:  black oxide

    Weight: 3.6 ounces

    Length: 2.25 inches

    100% designed and manufactured in the USA

    Learn More
  5. PLM
    $112.95

    The Chinese Stock bolts to any standard 10-32 bolt pattern stock adapter or hinge, such as those offered by Stormwerkz and ACE Rifle Stocks, It is easily adapted to any AK and can even be mounted to a Yugo PAP pistol by drilling and tapping two 10-32 holes in the rear trunnion (make sure the pistol is registered as an SBR before doing this.)  The rear of the stock has a machined rib pattern to give a good grip on the shoulder, and with the use of a hinge it can be configured to fold left or right. The Chinese Stock comes with the stock, two 10-32 bolts and washers. The Chinese Stock is 8.5 inches long, hinge adds about 0.625 inches to the length when installed. Overall length of pull from buttplate to face of trigger with Chiense Stock and Stormwerkz Hinge installed is 12.25 inches which is exactly the same LOP as a real Russian or Bulgarian Sidefolder AK.

    The stock comes with a choice of Bakelite Orange, Russian Plum, or Black side panels with all the hardware necessary to install them and the panels can be left of to get a skeletonized look.

    Material: 6061 aluminum

    Finish: type III milspec hardcoat black anodizing

    Weight: 10.0 ounces with panels

    Length: 8.5 inches (stock only not including hinge or mounting blocks)

    100% designed and manufactured in the USA

    Learn More
  6. Bren 805 Safety
    $33.95

    With smoothed out edges and profile and a slightly longer length to reduce the force needed to operate, the Bren 805 Enhanced Safety makes it just that much better to run your Bren 805. Made of 6061 aluminum and black anodized right here in the USA, The Bren 805 Enhanced safety is available for both the left and right hand sides of the gun (each side of the Bren 805 uses a slightly different assembly).

    Please note that due to the inherent design of the Bren 805 trigger mechanism and safety lever shaft the installation can take a little time and patience but the end result will totally be worth the effort.

    Material:  6061 aluminum

    Finish:  Type III milspec black anodizing

    Weight: 0.2 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More
  7. Bren 805 M-LOK Forend
    $79.95

    Machined from solid aluminum billet the Bren 805 M-LOK Forend allows for removal of the uncomfortable pictanny underside rail and replaces it with a nicely contoured underside forend with M-LOK slots on three faces.  It is a direct drop in replacement for the picatinny underside rail and only takes a few minutes to install and at 3.2 ounces only weighs slightly more than the stock 2.5 ounce component.

    Material: 6061 aluminum 

    Finish:  Type III milspec hardcoat black anodizing

    Weight: 3.3 ounces

    Length: 7.25 inches

    Designed and Manufactured 100% in the USA

    Learn More
  8. Bren 805 Knurled Charging Handle
    $38.95

    The Bren 805 Knurled Charging handle projects out 1/4" farther than the OEM handle and has a 1/2" diameter knurled drum for good purchase, and  we have found this to be the perfect size to give a good grip without racking knuckles on the receiver yet the handle does not project out too far from the side of the gun.

    Just like the OEM handle the Knurled Charging Handle will work on both the left and right side of the gun and is a drop in replacement made 100% in the USA.

    Material: 8620 steel with heat treat

    Finish:  Black oxide

    Weight:  1.4 ounces

    Length:  N/A

    100% designed and manufactured in the USA

    Learn More
  9. Brass Buster brass deflector
    $17.95

    The Brass Buster is designed as a removable and ambidextrous polymer brass deflector to allow weak side shooting with the Steyr AUG and Steyr AUG clones.  Simply press the Brass Buster down onto the stock behind the ejection port with the projection on the ejection port side.  Regardless of if your ejection port is on the left or right side of the gun the Brass Buster can be installed.

    The Brass Buster is compatible with all Steyr Aug, MSAR STG-556 (all generations) and E4, and all TPD AXR series rifle, and includes the brass deflector and an instruction sheet.

    Material:  Polymer

    Finish:  Black with very light texture

    Weight:  1.0

    Length:  N/A

    Learn More
  10. ARClight XTL IPSM "BIG BUTTON"
    $30.95

    The IPSM Big Button for ARClight XTL allows the pressure switch of the flashlight to be mounted internally in the forend while still being operated from the outside.  This is accomplished by the pressure swtich being mounting internally by an aluminum backer plate and a rubber button being mounted externally that can be pressed to activate the now internal pressure switch.  This keeps the pressure switch and cord inside the forend safe and free from snags and damage.

    The kit and pressure switch can be mounted on the left or right sides of the forend to offer more flexibility in position.  The IPSM kit includes the rubber big button, aluminum backing plate, adjustment screws, and instruction sheet and is 100% made in the USA.

    Material:  6061 aluminum and rubber

    FInish:  Type III Hardcoat Mislpec Anodizing

    Weight: 1.0 ounces

    Length: N/A

    100% designed and manufactured in the USA

    Learn More

Grid List

Set Ascending Direction

41-50 of 77